I managed 11j if it helps.
Sent from my iPhone using Tapatalk
I managed 11j if it helps.
Sent from my iPhone using Tapatalk
This actually does help! what offset are they? And how much camber are you running too?
Sent from my SM-G925F using Tapatalk
I'm running 9.75j ET 5 on the fronts now. I really wouldn't recommend going any further than that lol
Sent from my SM-G925F using Tapatalk
Is that on wider wings? I've got 8j ET -35 to go on there, slight bit more poke that you, just trying to figure out what wider wings to get
Sent from my SM-G925F using Tapatalk
I have 9.5 -10 on standard massively rolled front arches
Sent from my E6653 using Tapatalk
Yeah near enough same kind of poke as mine! I'm trying to avoid rolling arches as one of them is wrecked already so figured would be easier just replacing them with wider ones!
Sent from my SM-G925F using Tapatalk
25mm wider front wings would be more than enough and personally I would go with 30mm rear arches
Sent from my E6653 using Tapatalk
I thought I'd need something closer to 40mm wings lol was looking at srb ones! Will have to go back and double check that now and for rears they're 10J ET -20 so pokes a bit more. Test fitted them and they're about 50mm further out from standard arch but looking to do something different to over fenders either way! Jun arches will more than likely suit the wheels I've got better
Sent from my SM-G925F using Tapatalk
You have more poke? Jesus lol surely only a centimetre or two? I have my front arches rolled no flare.. And I'd say they look pretty illegal sticking out this much...
Lol yeah just compared on willtheyfit, you're right its only about 1cm different! Also hoping not to need stretched tyres and no camber either ideally but then I want to go quite low so not sure how it'll work out for now. And yeah that is out quite a bit, want mine flush with the arches. If anything I'll go for the 40mm wings and use spacers if needed
Sent from my SM-G925F using Tapatalk
Sorry to high jack the thread, been looking at some 9.5j et30 with 225 tyres, will these fit with standard arches (non rolled) or will I have problems?
Sent from my iPad using Tapatalk
Roll the lips and they will go on fine. Might need a 5mm spacer up front to stop the inside wheel lip from contacting your suspension depending on what you are running
I've got HSD coilovers so don't know if that will help, I think 9.5 will be too close for standard arches
Sent from my iPhone using Tapatalk
Yeah you will probs need 5mm on the front to clear contact with the coilovers but a set of them are only like a tenner. I used a block of wood and a hammer to flatten the little inner lip on the arch to fit my first wheels of course you would want to use a arch roller ideally but its not a hard job to do dude
I'd say you may have more trouble clearing the coilovers than hitting the arch.
Mine are 9.75j et25 and they hit the coilovers on the front instantly.
I had to fork out £115 for H&R hubcentric spacers on the front and get extended wheel thread stud's too. Now running ET10 and they are fairly clear of the coilys.
The lips on the front are like butter. They'll roll just fine but be careful if you have any bubbling or surface rust on the fronts.
What et are the rear gtr-d? Still unsure on what to do with my rears!
Sent from my SM-G925F using Tapatalk
Its weird as two people selling 9.5's say they fit no problem in standard arches, I think I'll stick to 8-9j just to be safe
Sent from my iPhone using Tapatalk
I found that 9.5j et25 hit my coilovers pretty well. Et20 is the minimum I'd run at the front on a 9.5j.
1998 Nissan 200sx s14a , 2000 std 5 speed with nismo supercoppermix clutch bn6 Sapphire Blue