Page 1 of 7 123 ... LastLast
Results 1 to 20 of 122

Thread: Enquiries section

  1. #1
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0

    Enquiries section

    Please ask here for prices, if i can do, how long itl take, when etc etc etc

  2. #2
    Guest
    Join Date
    Sep 2009
    Location
    east london
    Posts
    513
    Rides
    0
    Where abouts you based mate? I cant find it anywhere and think it might be useful to know

  3. #3
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    The location is in the "About" thread but for any one who did not see it, the workshop is located between Aylesbury and Bicester on the A41 in Buckinghamshire.

  4. #4
    Guest richy200's Avatar
    Join Date
    Aug 2006
    Location
    swansea
    Posts
    2,112
    Rides
    0
    You know dw has the geomaster hubs, can you make a set using s14 hubs that can not only incorporate a lot more lock but also help reset the roll centre?

    Also if this was possible for you, how much would we be looking at roughly

    cheers dude.

  5. #5
    Guest Markus74's Avatar
    Join Date
    Nov 2007
    Location
    Herts
    Posts
    884
    Rides
    0
    Hello mate

    How much to fit elbow, tube mani and downpipe?

  6. #6
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by richy200 View Post
    You know dw has the geomaster hubs, can you make a set using s14 hubs that can not only incorporate a lot more lock but also help reset the roll centre?

    Also if this was possible for you, how much would we be looking at roughly

    cheers dude.
    Hi Richy,

    Yes i can make roll centre correction hubs, but only for the front and they are not sold for road use
    Extra lock and reduced Ackerman hubs are 150 on exchange,
    Roll centre correction aswell as extra lock and reduced Ackerman are 300 on exchange.

    Quote Originally Posted by markus74 View Post
    Hello mate

    How much to fit elbow, tube mani and downpipe?
    Hi Marcus,

    To fit that lot, previding you have all the gaskets, its 120 including new antifreeze

  7. #7
    Guest Markus74's Avatar
    Join Date
    Nov 2007
    Location
    Herts
    Posts
    884
    Rides
    0
    Hello mate, I will have all the gaskets but.........they are the ones off the car that the elbow, mani etc are coming off. The guys assured me that that they are not split and are fine. I would have got new ones but got a quote from apex at 110 quid

    You changed my head to mani gasket, mani to turbo, turbo to elbow not hugely long ago, hmm maybe a year actualy so some of those may be ok. The downpipe is new so i'm hoping (fingers crossed) that it'll come with gaskets.

    The bits should come this week sometime but what is your availability mate

  8. #8
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by markus74 View Post
    Hello mate, I will have all the gaskets but.........they are the ones off the car that the elbow, mani etc are coming off. The guys assured me that that they are not split and are fine. I would have got new ones but got a quote from apex at 110 quid

    You changed my head to mani gasket, mani to turbo, turbo to elbow not hugely long ago, hmm maybe a year actualy so some of those may be ok. The downpipe is new so i'm hoping (fingers crossed) that it'll come with gaskets.

    The bits should come this week sometime but what is your availability mate
    Ah yes i do remember
    If thats the case, i would recomend you get a new Nissan turbo gasket, oil and water feed copper washers and Nissan locking tabs
    I can supply these parts if its any easier.

  9. #9
    Guest Markus74's Avatar
    Join Date
    Nov 2007
    Location
    Herts
    Posts
    884
    Rides
    0
    Quote Originally Posted by Polo View Post
    Ah yes i do remember
    If thats the case, i would recomend you get a new Nissan turbo gasket, oil and water feed copper washers and Nissan locking tabs
    I can supply these parts if its any easier.
    Nice one, if you could supply them that would be great!, how much mate and whens the soonest you could fit me in?

    Holy crap!, just read the bit about you taking over the workshop, spot on mate!
    Last edited by markus74; 04-07-2010 at 20:48.

  10. #10
    Guest richy200's Avatar
    Join Date
    Aug 2006
    Location
    swansea
    Posts
    2,112
    Rides
    0
    Quote Originally Posted by Polo View Post
    Hi Richy,

    Yes i can make roll centre correction hubs, but only for the front and they are not sold for road use
    Extra lock and reduced Ackerman hubs are 150 on exchange,
    Roll centre correction aswell as extra lock and reduced Ackerman are 300 on exchange.
    sounds good mate, why not recomended for road dude? the car is a daily that's why i ask

  11. #11
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by richy200 View Post
    sounds good mate, why not recomended for road dude? the car is a daily that's why i ask
    If you use the car with modded knucles on the road thats down to you.
    Its for the same reason most after market car bits say "for off road use only"

  12. #12
    Guest
    Join Date
    Feb 2010
    Location
    surrey
    Posts
    41
    Rides
    0
    Hey dude, my turbo gaskets have gone and need replacing. As I work stupid hours the car would need to be collected and delivered back after. Also I would like a check over of the car and check all is well. How much would all this be and when you would be able to do it?
    Cheers
    chris

  13. #13
    Guest richy200's Avatar
    Join Date
    Aug 2006
    Location
    swansea
    Posts
    2,112
    Rides
    0
    Quote Originally Posted by richy200 View Post
    sounds good mate, why not recomended for road dude? the car is a daily that's why i ask
    Ok greaqt, thanks for getting back to me. Will get this done with you. Will start saving up funds and will be in touch shortly

  14. #14
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by chunk87 View Post
    Hey dude, my turbo gaskets have gone and need replacing. As I work stupid hours the car would need to be collected and delivered back after. Also I would like a check over of the car and check all is well. How much would all this be and when you would be able to do it?
    Cheers
    chris
    Hi,

    Yea this is not a problem but please can you PM me your post code for collection so i can price it. It will be cheaper for you if you drive it to me and i can lend you a car FOC

    Quote Originally Posted by richy200 View Post
    Ok greaqt, thanks for getting back to me. Will get this done with you. Will start saving up funds and will be in touch shortly
    No problem

  15. #15
    Guest
    Join Date
    Jul 2006
    Location
    nowhere interesting
    Posts
    991
    Rides
    0
    Im thinking of fitting an s14a auto diff to my manual s14a,

    could you provide a price too supply and fit it please mate,

    drop me a pm please

  16. #16
    Guest immy21's Avatar
    Join Date
    Mar 2009
    Location
    Edinburgh
    Posts
    7,165
    Rides
    0
    Hi
    Iv fitted energy suspension bushes to my diff but threw away the 2 washers I need to keep

    Can you sort something out for me please?
    pics of what I need:
    http://www.sxoc.com/vbb/showthread.p...96#post5401296

  17. #17
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by ady_mi16 View Post
    Im thinking of fitting an s14a auto diff to my manual s14a,

    could you provide a price too supply and fit it please mate,

    drop me a pm please

    Hi,

    Fitting would be 60 + 10 oil + the diff, prices are about 80-100.

    Cheers

    Quote Originally Posted by immy21 View Post
    Hi
    Iv fitted energy suspension bushes to my diff but threw away the 2 washers I need to keep

    Can you sort something out for me please?
    pics of what I need:
    http://www.sxoc.com/vbb/showthread.p...96#post5401296
    Hi,
    I have the washers, pm me your address and il send them out

  18. #18
    Guest
    Join Date
    Jul 2006
    Location
    nowhere interesting
    Posts
    991
    Rides
    0
    Im thinking of fitting an s14a auto diff to my manual s14a,

    could you provide a price too supply and fit it please mate,

    Fitting would be 60 + 10 oil + the diff, prices are about 80-100.

    could you also sort some rust on the front of my front suspension turrets, would need cutting out, small plate made up and re welding? Id do the priming and painting afterwards, so just the metal work

  19. #19
    Guest Polo2's Avatar
    Join Date
    Feb 2006
    Location
    Buckinghamshire
    Posts
    5,652
    Rides
    0
    Quote Originally Posted by ady_mi16 View Post
    Could you also sort some rust on the front of my front suspension turrets, would need cutting out, small plate made up and re welding? Id do the priming and painting afterwards, so just the metal work

    Yes i can do all welding repares, this is just charged at 40 per hour, most patchs can be done in an hour Thogh id need to look at it 1st.

  20. #20
    Guest immy21's Avatar
    Join Date
    Mar 2009
    Location
    Edinburgh
    Posts
    7,165
    Rides
    0
    All sorted in a mater of minutes by a very genorous polo

    One day when I have enough power to bust my gearbox regularly il come see you, big thanks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •