Results 1 to 10 of 10

Thread: Useful 180sx/Ps13 Information

  1. #1
    Guest norfy's Avatar
    Join Date
    Jun 2008
    Location
    Ashford, Kent
    Posts
    1,283
    Rides
    0

    Useful 180sx/Ps13 Information

    Service Parts.

    non vvt rocker cover gasket - Nissan - 13270-52F00 Just over £12
    rocker cover plug hole gasket (this is the vvt one which is better) - Nissan - 13271-65F00 £8
    Oil filter - Nissan - 15208-70j00. Also same as '96 micra (k11) Halfords part number HOF339 (about £9)
    Alternator belt - Nissan - 11720-52f. Micro-V part No. 5PK933
    Power steering belt - Nissan - a172m-59ssa-vw
    Spark Plugs - BKR7EIX - NGK Iridium - On standard car with Aftermarket Air filter and exhaust
    Engine Oil Grade - Carta has used Silkolene Pro S 10-50 and 10-40 - Any other recommendations?
    Gearbox Oil Grade -Carta has used Silkolene SILKTRAN SYN 5 75W-90 Fully Synthetic Gear Oil
    Differential Oil Grade -Carta has used Silkolene BOA 90LS in his Nismo 2 Way - What do people use in standard differentials?
    Battery - 054
    Oil Filter - http://www.opieoils.co.uk/p-6789-oil...r-2326600.aspx

    Redtop Oil Strainer Upgrade
    Upgrade for Redtop oil strainer 15050-65f01 its the oil strainer from the Blacktop non vvt, has a wider mouth than the Redtop strainer. note, this is a s14 vvt stock part.

    Engine Block Codes
    Redtop is 50f
    Blacktop Non VVT is 52f


    Service Manual

    This is very limited and the only one available is in japanese showing only the engine mechanical section and a quick eccs overview

    http://180sx.strent.net/servicemanuals.php


    180sx/ps13 Sr20det REDTOP ECU Pinout (kouki/type-x has a different pinout but the same connector)

    http://browsebug.info/wp-content/upl...ecu-pinout.jpg

    180sx redtop and blacktop straight cam (kouki) pinouts side by side. It is possible to swap some pins round on a kouki engine loom to use a chuki (redtop) ecu and these pinouts will help with that. If you're wanting to do this then you'll also need to earth out the Brown/Yellow wire from the Lambda sensor as the redtop is earthed but the kouki has an earth control from the ecu.

    http://wheretobe.co/wp-content/uploa...ecu-pinout.jpg



    Fusebox layout


    http://180sx.strent.net/documents/fuseS13.gif

    Airflow meter upgrades (mainly Z32)

    http://www.sr20tuning.com/z32afm.html

    Fitting a rear foglight to a 180SX (required for MOT):

    http://www.sxoc.com/vbb/showthread.php?t=261340

    Kouki bulb holders. The original harnesses are available from japan but are roughly £50 each. A cheaper alternative is to buy x4 7440 bulb holders from Ebay (about £10), and x2 7443 bulb holders from Ebay (about £6) plus bulbs and wire them into your car.


    Using a vvt block on a non-vvt sr20

    http://www.sxoc.com/vbb/showthread.p...88#post6517188
    Last edited by norfy; 16-04-2018 at 10:45. Reason: Tidy

  2. #2
    Guest Carta's Avatar
    Join Date
    Jun 2007
    Location
    Dudley, West Midlands
    Posts
    3,405
    Rides
    0
    Have tided the thread up, any more information let me know.

  3. #3
    Guest Sidewaysfun's Avatar
    Join Date
    Nov 2007
    Location
    Cambs
    Posts
    2,141
    Rides
    0
    T25g oil feed thread is the same size as a T25. (probably obvious but hey)

    7/16 UNF with 24 tpi

    Handy to know if ordering a new banjo bolt when upgrading to braided lines.

  4. #4
    Guest doz_sr20's Avatar
    Join Date
    Apr 2010
    Location
    Cheltenham
    Posts
    270
    Rides
    0
    Red Top SR20 Cam Cover Gasket:

    Part Number: 13270-52F00 (outter part)
    Part Number: 13271-65F00 (inner part around the plug holes)

  5. #5
    Guest Micraplay's Avatar
    Join Date
    Sep 2004
    Location
    Chorley / Preston / Ormiskirk
    Posts
    3,097
    Rides
    0
    s13 SR20 oil filter thread is same as CA18 - found this out when i bought an s14 relocation kit, needless to say it didnt fit!!

  6. #6
    Guest
    Join Date
    Aug 2005
    Location
    aberdeen
    Posts
    5,538
    Rides
    0
    Quote Originally Posted by micraplay View Post
    s13 SR20 oil filter thread is same as CA18 - found this out when i bought an s14 relocation kit, needless to say it didnt fit!!
    Also the same as a pulsar

  7. #7
    Guest John Bennett's Avatar
    Join Date
    Aug 2003
    Location
    N.E.
    Posts
    19,147
    Rides
    0
    Service Manual

    This is very limited and the only one available is in japanese showing only the engine mechanical section and a quick eccs overview

    http://180sx.strent.net/servicemanuals.php
    Heh, I scanned that. Forget it now though, the whole lot is here:
    http://www.sxoc.com/vbb/showthread.p...ls-to-download

    The latest Brother £200 A3 ADF scanner is a wonderful thing

  8. #8
    Guest
    Join Date
    Nov 2007
    Location
    Wales
    Posts
    605
    Rides
    0
    anyone any idea on fuel filter?

  9. #9
    Guest Sidewaysfun's Avatar
    Join Date
    Nov 2007
    Location
    Cambs
    Posts
    2,141
    Rides
    0
    Quote Originally Posted by Joesefer View Post
    anyone any idea on fuel filter?
    I used a 300zx one mate. They are a bit bigger than stock ones. I'm guessing that an S14 one would be the same as stock.

  10. #10
    Guest doz_sr20's Avatar
    Join Date
    Apr 2010
    Location
    Cheltenham
    Posts
    270
    Rides
    0
    Just found all this out the hard way:

    Stock rear brakes comprise of: P10 eGT Primera discs, S14 rear pads.

    To add to peoples posts above, oil filter also the same as P10 eGT Primera.

    Sent from my HTC One_M8 using Tapatalk

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •