Prices and advice please guys

[Aj82]

Right, after our conversation i have decided to get the Tomei 270 solid cams, solid lifter kit, supertech double valvesprings and possibly supertech valves but not sure whether to get 1mm bigger ones or not??

Also do you sell all the seals etc aswell?

Could you give me a price for these please including delivery to Scottieland!!


Cheers Aj

[MazworxRacing]

Aj,
Its personal preference on oversize valves or not. Id probably run +1mm over on 270 cams.

For the cams, solid pivots, Supertech 116lb springs, Supertech valves, Supertech seals will be 1391.60USD shipped.

Let me know if you have any other questions.

Thanks!

[Master Chief]

I have a question.
I dont know much about supertech, but i was also looking into a simmilar setup.
I am currently in the proces of installing a GT3582R on my SR20DET.

I curently have Tomei's 260, but i do want to change to solids.

What RPM's would the above setup be good for ?

Also, are those springs double type springs ? How re they compared to the TOMEI double springs - exept the fact they cost about 700$ less ?

Thanks.

[MazworxRacing]

8500+

[Aj82]

Aj,
Its personal preference on oversize valves or not. Id probably run +1mm over on 270 cams.

For the cams, solid pivots, Supertech 116lb springs, Supertech valves, Supertech seals will be 1391.60USD shipped.

Let me know if you have any other questions.

Thanks!

Will the valves need bigger guides and do they come with the retainers and shims needed too? Could you also quote me the price in pounds so we are both sure of the amount please guys.

Cheers Aj

[MazworxRacing]

Will the valves need bigger guides and do they come with the retainers and shims needed too? Could you also quote me the price in pounds so we are both sure of the amount please guys.

Cheers Aj

On our normal buildsm, we switch the exhaust valves from 7mm stem to 6mm stem and those run different guides. If you want to use the factory spec 7mm exhaust and 6mm intake which is fine, from experience of taking apart stock heads, the way the geometry of the stock valve guides are weak and gets warped.

Id probably go 6mm-6mm on it and run mang. bronze guides, but you can have the factory ones reemed and will work just fine.

[Aj82]

Hmm interesting how much are the 6mm guides? And wha are they like to remove and fit?
Could you also provide the prices again in Sterling for me please guys.

Cheers Aj

[MazworxRacing]

The guides themselves are 92.64 USD or 60.7741 GBP
You may want to consider a complete "kit" for your build. They are not hard to do

If you want to consider the complete "kit" which will include the following:

Supertech Dual Valve Springs
Supertech Titanium Retainers
Inner Spring Seat locators
Intake/Exhaust Guides
Intake/Exhaust valve stem seals
Intake and exhaust valves +1mm over
New Rockers
New Rocker guides

Tomei Solid Pivot
Tomei Solid Cams

Total price of 1840.66USD shipped or 1,206.03 GBP or if you want to stick with the old package price it will be 911.802 GBP

[Aj82]

Well i will see what i have spare to play with and decide from there. Is that delivered to my door? Will i have other duties to pay on them?

Id also like to ask about your inlet manifold spacer that allows fitement of top feed fuel rail and injectors. I have been told that my nismo 740's may not be enough but i dont know if sard side feed 850's will be or if i will have to fit top feed RC 1000's.

Damn this rebuilding malarky aint easy!! haha


Cheers Aj