Search:

Type: Posts; User: green_rs13

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    11
    Views
    117

    just take the pipes off under the bonnet and...

    just take the pipes off under the bonnet and activate the washers, se if fluid pisses out.
  2. Replies
    2
    Views
    62

    taking the hICAS fuse out in the drivers side...

    taking the hICAS fuse out in the drivers side engine bay fusebox would elimnate the HICAS.
    does the starter turn ok if you stick 12V on the exciter terminal?
    have you tried putting a jump lead from...
  3. Replies
    5
    Views
    105

    i think there is a big electrical plug in the A...

    i think there is a big electrical plug in the A post
  4. Replies
    344
    Views
    48,197

    as alan says S13 parts are fetching good money...

    as alan says S13 parts are fetching good money these days.


    i actually need an s13 drivers door too, how much is it to ship a pallet? LOL..
  5. Replies
    5
    Views
    100

    wild cams and heavy valve springs seem to kill...

    wild cams and heavy valve springs seem to kill VVT sprockets.
  6. ive not got one and have the red vw coilpack...

    ive not got one and have the red vw coilpack conversion and it works fine.

    tbh if i did it again i think i would use the regular black vw coils as they fit the sr20 better,
  7. Replies
    14
    Views
    360

    he is on facebook still, i seen him post a car...

    he is on facebook still, i seen him post a car for sale yesterday.
  8. Replies
    2
    Views
    107

    its probably not your ECU, take the lid off it...

    its probably not your ECU, take the lid off it and look at all the bits inside it to see if look good.
  9. Replies
    9
    Views
    253

    cost depends on how knackered it is when they...

    cost depends on how knackered it is when they strip it down.

    conceptua were selling all the bits to rebuild them but they have a few variations inside them so it would be a pain trying to decide...
  10. Replies
    9
    Views
    253

    Garage-D up in Watford rebuild them.

    Garage-D up in Watford rebuild them.
  11. Replies
    2
    Views
    123

    tbh i would just fit a lightweight one if your...

    tbh i would just fit a lightweight one if your having trouble sourcing a standard one. the standard ones weigh a tonne anyway
  12. Replies
    4
    Views
    145

    the sensors are fot the oil coler system. just...

    the sensors are fot the oil coler system.
    just pop them out and take them to an industrial hose supplier and ask for some blanks. they are probably a tapered thread
  13. Replies
    5
    Views
    95

    if you push the clutch in when its making the...

    if you push the clutch in when its making the noise does it go away? is it louder when cornering et..
  14. Replies
    19
    Views
    390

    ..

    ..
  15. Replies
    19
    Views
    853

    tbh you sould be changing the fuel lines on it...

    tbh you sould be changing the fuel lines on it any way as its 20+ years old.
  16. im pretty sure a 2 pence piece is the right size...

    im pretty sure a 2 pence piece is the right size to blank it off on the exhaust mainifold side.
  17. Replies
    9
    Views
    121

    i think i might have a pair of new old stock OEM...

    i think i might have a pair of new old stock OEM ones.
    how much of a rush are you in?
  18. Replies
    1
    Views
    114

    i always jack them on the tie down points on the...

    i always jack them on the tie down points on the front radiator support panel
  19. Replies
    7
    Views
    209

    you are ok to connect those bits together. id...

    you are ok to connect those bits together.

    id always use 20/50 fully synth in my old CA so i doubt its a viscosity issue. probably have some air in them.
  20. Replies
    4
    Views
    179

    i had a dakota box ruuning off a front abs sensor...

    i had a dakota box ruuning off a front abs sensor and could never get the speedo to be accurate across the entire speed range.
  21. Replies
    3
    Views
    165

    its the same car underneath so, yes.but some...

    its the same car underneath so, yes.but some people have reported japspeed ones make a weird duck like noise.
  22. Replies
    4
    Views
    153

    when you have the rear discs off run a grinder...

    when you have the rear discs off run a grinder around the bits that need cutting off.

    just swap the calipers and the discs for the rear.

    make sure you have the z32 front caliper mounting bolts.
  23. Replies
    120
    Views
    43,431

    you missed the part where you put 10 tonnes of...

    you missed the part where you put 10 tonnes of copperslip on the threads.
  24. Replies
    7
    Views
    144

    drill the threads out and put a nut behind it if...

    drill the threads out and put a nut behind it if you can get access.
  25. i seen a 240z being restored once and they built...

    i seen a 240z being restored once and they built 2 big wooden picture frame squares, bolted them to the subframe mounting points and rolled it onto its side. (picture the car being encapsulated...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4