That spoiler is a Nismo R-Tune. Worth a few £££'s
Type: Posts; User: craig8585
That spoiler is a Nismo R-Tune. Worth a few £££'s
I know this is a little presumptuous, but can you reveal if there will be a Boxing Day / New Year promo?
Thank you
I'm an administrator on S15OC. Your first 10 posts have to be approved before appearing on the forum. This is not for our personal benefit as administrators and the reasons are listed in the forum...
Yeah, I meant bolts, not studs. In the end I just torqued them in sequence and staged at 20-40-60-80 lbs/ft
The engine is for my Almera Haz :)
Hello,
I've rebuilt a SR20 with a 1.5mm Cosworth gasket.
I believe the usual torque for the head is 33lbs/ft, +90deg, +90 deg, so should it be the same for a multi-layer MHG?
Thank you!
Perfect, thank you Jem :D
I've searched high and low but still don't know the recommended torque for the front hub nuts.
I've seen 85 lbs/ft and 200 lbs/ft quite a lot but there is a fairly large difference between the...
Hello!
Are you able to supply ACT clutch kits for the Almera GTi's - SR20DE..?
Thank you!
:)
All of the wiring looks ok.. It was just odd how all 4 coilpacks were earthed down a single tiny wire earthed behind the block, but that's now far more substantial and to a better earth.
If it's...
Depends what colour you want as they should come painted so have different PN's. The PN looks similar to the WV2 one though..
I guess from the lack or response your too busy to do this..? Never mind, I'll get it done elsewhere.
I'd take a black face 2 bar boost gauge if it goes ahead.
Is this the one you meant?..
http://www.se-r.net/car_info/de_det_differences.html
Also found this too..
S13 - S14 - S15 SR20DET differences
Thanks for the replies. I've done some reading up already but my main question was regarding the bare block and head. Totally forgot the oil feed for the turbo. For the sake of it I'll pay the extra...
I'm looking to buy a bare block and head to start building up over time and can't help noticing how cheap DE's are in comparison to DET's, so..
Are there any differences in the block and head when...
eBay converters appear to do the job but if you look into them a bit deeper, you'll find they only do half of the job. Like I said above, the speedo reads roughly correct but the ECU is getting a...
Are you able to replace valve springs without removing the head? And what's the normal price for fitting a new pair of cams (without springs)?
Cheers :)
If you can live with it displaying kph then just leave it. The cheapo converters mess up the speed reading that's sent to the ECU, which is then supposed to effect ABS etc.. If you have DataScan you...
I've managed to misplace the fitting instructions for my Whiteline FARB and fitting it turned out to be slightly more complex than first appears as the setup is diffierent to the original. I got the...
Hello, do you sell the 'C' spanners for the Gen 1 coilovers separate to the kits? If so, could I have a price please. Thank you.
I'm not sure what was causing the vibration as I've now had the disks done and new bushed tension rods, new lower ball goints and track rod ends too.. so hopefully that will sort it! I got the disks...
I got a pm from you about them but I didn't at any point say I actually wanted one - just that advertising on s15oc might help..
Yeah, I was looking at their site but was unsure if they could cope with the 356mm rotors.. Did they do yours on the car? As this wont be possible either due to it being in bits!
I've been...
Cool, thanks for that :) I've found a few local places but they can't accommodate 356mm rotors :(
It's costing over £600 for the day and we have the whole track with catering from 10-5. It's got nothing to do with S15OC either, I just put a thread on there to encourage other members. I didn't...