Search:

1 bar or 14 psi is what us recommended for students 2

Sent from my SM-G960F using Tapatalk

Because people are idiots, that car was in todays market no more than a 2.5-3k car at a push.

Thing was hanging

Awesome cheers daz

Sent from my SM-G960F using Tapatalk

After opinions.

Prior to my ownership someone folded the arch lips up, to make this easier I assume they slit the lips then folded.

I tried to flare them and this just resulted in creases at...

Tickets bought here too

Heres to hoping for a decent comeback year for events, and Simply Jap is probably the best Japanese car event that we have down south.

I will book a stand provisionally for 15 cars and no it does...

That is an s13 casing.

Sent from my SM-G960F using Tapatalk

S13 diff is solid mounted as standard.

S14/a , s15 are bushed.

Either way you'll need the s13 backplate as the 14 plate won't fit a 13 subframe.

If you've put the diff in a 14/a 15 casing...

I always use a blow lamp, seem to almost fall out with some heat.

Thats great but please may I suggest you look into cleaning all the breather hoses properly specifically the one at the back of inlet side cam cover that goes down into a hard pipe then to the block...

The ca18det pcv is a threaded fitting in the rear of intake plenum that the breather hose connects

Sent from my SM-G960F using Tapatalk

Well this is going to be a long one.

Do you have ac?

No charcoal canister is located behind slam panel to the right of radiator.

It is a one way valve, you should be able to blow through...

That plug isn't iacv its ficd which is there to raise revs when ac is on.
(It won't cause your issues)

What spec is the car?

Pressure test intercooler and all boost pipes, sounds much like a...

Can you elaborate a little more please [emoji120]

Sent from my SM-G960F using Tapatalk

I think I'm going to have to go 1.3mm as the block was decked for the mhg but I am going to measure this today, dont think the oem gasket will hold up at over 400bhp?

Also with a big turbo surely...

But can induce det from my understanding.

Raising or lowering compression can have detrimental affects, lower it = more boost but more chance of knock

So atm I run a 1.6mm but I am going to...

Yes piston to deck height is 0.00mm so I am checking this at the weekend, I have already had the head height measured and as stated in above post I am at 125.96, manual states minimum is 125.9
...

Min head height is 125.9 i am currently at 125.96.

Currently have a cometic 1.6mm but had no end of issues with it so looking at tomei but these are only available in 1.0 1.2, 1.5, 1.8

Speaking...

Can anyone tell me what the oem clearance between piston and cylinder head is?

Replacing the headgasket and wish to achieve oem spec

Do a pressure test on the intercooler and pipework, these cars are 30 years old the intercoolers are prone to leaking.

No knock isn't from bad afr necessarily

Sent from my SM-G960F using...

You're running 0.9bar of boost through the stock small turbo, its going to drop off.

Get a t28 or t28r on it, bin the likely leaking intercooler and get a tune.

Afr may look fine but does your...

2871r is a straight swap just may have to rotate the core slightly. Pm jay1017 he has a hybrid 2871r for sale freshly built.

If going standalone most standalone ecus have the capability to control...

Check/clean breather hardline between block and inlet cam cover.

Common issue that can result in dipstick popping out and will cause bearing wear

Sent from my SM-G960F using Tapatalk

I'm running a 1.6mm cometic so can't go back to oem unfortunately

Sent from my SM-G960F using Tapatalk

Any opinions on this?