Search:

Type: Posts; User: liamjrhodes

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    5
    Views
    515

    All the ball bearing turbos I have seen have had...

    All the ball bearing turbos I have seen have had restrictors built into them. The restrictor is used as the locating pin of the bearing cartridge

    Sent from my SM-G960F using Tapatalk
  2. Replies
    4
    Views
    648

    More wd heat and shock are the best ways to...

    More wd heat and shock are the best ways to remove stubborn fasteners

    Sent from my SM-G960F using Tapatalk
  3. Replies
    34
    Views
    23,627

    Love an s12! Looks awesome with the arches ...

    Love an s12! Looks awesome with the arches

    Sent from my SM-G960F using Tapatalk
  4. Replies
    258
    Views
    77,023

    Well it's been a while.... The car has been...

    Well it's been a while....

    The car has been right at the bottom of a long list of stuff that needed my attention

    So since I last updated this ive got married, had a daughter replaced the roof...
  5. Replies
    7
    Views
    467

    Bit if a thread revival but thought I would...

    Bit if a thread revival but thought I would update with the small amount of progress...

    So I stripped off all the intercooler and associated pipework from turbo to inlet
    Removed the inlet...
  6. Hello, do you happen to have a set of just the...

    Hello, do you happen to have a set of just the fronts for an s13? My brother is converting his 1972 toyota carina to s13 front suspension

    Sent from my SM-G930F using Tapatalk
  7. Replies
    7
    Views
    467

    Yeah it's looking like it could be a couple of...

    Yeah it's looking like it could be a couple of things.
    I've had it all in bits so could be leaking from anywhere haha

    Sent from my SM-G930F using Tapatalk
  8. Replies
    7
    Views
    467

    This may be an issue, the wire snapped from my...

    This may be an issue, the wire snapped from my knock sensor and has been repaired, it may need a better job doing!
  9. Replies
    7
    Views
    467

    Ill have another check of the pipework and...

    Ill have another check of the pipework and pressure test it all see if I can find anything

    I hadn't even considered fuel!
  10. Replies
    7
    Views
    467

    S14a SR20DET Running Issues

    Hello Everybody its been a while since I have posted as life has been pretty hectic and the Nissan has been tucked up in the garage for much too long!

    I really would like to get it sorted so...
  11. Replies
    96
    Views
    76,244

    Awesome work so far! Just one point, I'd...

    Awesome work so far! Just one point, I'd recommend moving the oil cooler to the side so it's not in front of the radiator, lots of people have heat soak problems as the oil cooler is always hot
    ...
  12. Replies
    16
    Views
    1,699

    I may come weather dependent :) Sent from my...

    I may come weather dependent :)

    Sent from my SM-G930F using Tapatalk
  13. Replies
    258
    Views
    77,023

    Another update!! I had a fiddle with the...

    Another update!!


    I had a fiddle with the adaptor plate for the air filter and got it to sort of fit
    http://uploads.tapatalk-cdn.com/20160520/97bc39471029a2e5d16cf6157e2967ab.jpg

    I then got...
  14. Replies
    258
    Views
    77,023

    Well my current options are keep it as it is or...

    Well my current options are keep it as it is or rattle can the wings red so cheap paint sounds good haha
  15. Replies
    258
    Views
    77,023

    It's been do long since I last posted and in...

    It's been do long since I last posted and in terms of progress on the Nissan not sloths happened unfortunately. So here goes!

    Changed the fuel filter to a Z32 unit as it was due a new filter and...
  16. Replies
    17
    Views
    9,100

    Stick with Adrian flux, they have always been the...

    Stick with Adrian flux, they have always been the cheapest and best deal on my s14a since I was 20
  17. Replies
    20
    Views
    1,188

    Worn them since high school, worn contact lenses...

    Worn them since high school, worn contact lenses for last 6 year soooo much better! -2.75 in both eyes
  18. Replies
    66
    Views
    11,009

    Go see wardy for the exhaust :)

    Go see wardy for the exhaust :)
  19. Replies
    0
    Views
    1,922

    Coilovers for ls400

    Bought a 95 ls400 for my daily and would like to know if anyone has any experience of coilovers/lowering as I have heard Internet rumors that other toyota based suspension fits.

    This would be very...
  20. Replies
    8
    Views
    557

    As said wardy (apw engineering) makes awesome...

    As said wardy (apw engineering) makes awesome manifolds!
  21. Replies
    15
    Views
    765

    As Chris has said you can run the 3a chip with a...

    As Chris has said you can run the 3a chip with a standard manifold with no detrimental effect
  22. Replies
    161
    Views
    35,369

    Speak to Wardy (apw engineering) about the...

    Speak to Wardy (apw engineering) about the manifold pal, should be able to get it lots cheaper than 6boost and it's supporting forum members businesses :)
  23. Replies
    29
    Views
    3,227

    As said jubilee clips work fine, been used for...

    As said jubilee clips work fine, been used for years on machines running pressured much higher than an sr20 will ever run. Just make sure you have a lip on the end of the pipe or nothing will hold it
  24. Replies
    27
    Views
    10,061

    As he explained, it's stronger as the offset...

    As he explained, it's stronger as the offset spacers place an offset load on the rack which breaks things
  25. Replies
    20
    Views
    1,446

    Yeah, you can't really buy decent quality stuff....

    Yeah, you can't really buy decent quality stuff. So like I said he must be making his own :) credit to him it's a part of the market that isn't very well served
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4