Hi guys, I want to change my fuel pump as it's a bit on the small side and has been in service for a number of years. Currently running a Walbro 255 on a rb25 swapped s14 making 425bhp.
I want to...
Type: Posts; User: wicked-vtr
Hi guys, I want to change my fuel pump as it's a bit on the small side and has been in service for a number of years. Currently running a Walbro 255 on a rb25 swapped s14 making 425bhp.
I want to...
Very happy with my parts, top service!
If you see any decent divided manifolds for rb25det drop me a message
As above for s14a, group buy??
Cool il go ahead and cut it out then!
Unfortunately I already have a sr here without a bay to call home, I could do without another!
Hi guys, now that I'm running my car with a rb25, can I rip out the nats? Iirc the skyline ecu doesn't need it, but I wanted to make sure before i took it out.
Any info appreciated
Hi guys, not sure if this is the right section, mods feel free to move.
What's the best underseal to be using? The previous owner used some stuff from america that's hard as nails, I just can't...
Tried re coding them, no effect. Anyone else got any ideas? Or any specialists in Surrey/Hampshire/Berkshire area?
Don't want to have to take it to Nissan...
Hi guys, I reset one of my nays fobs following the guide on the forum.
the reset fob succeeded in unlocking the car but can't lock it again. Unfortunately now the master fob doesn't seem to do...
How much was that if you dont mind me asking?
Good stuff, i like the sounds of that.
Is that a enuine vertex kit you have or a copy?
Hi guys, does anyone know if the vertex bumpers/skirts are deeper than the standard s14a ones? I.E will a vertex kit give me less ground clearance?
If so, how much deeper are they?
My car looks similar to the above, if a little lower i think.
And ideally i'd drive around with it scuffing the cats eyes, but that might be a bit too hardcore for me in reality.
Never had any ground clearance issues, im only looking to go 10-20mm lower. Il get some pics up tomorrow, hopefully someone can tell me what im doing wrong
I thought this might be the case, it doesn't look all that low to me really, not compared to some anyway. I'd say the front splitter is a little under 2 inches from the floor.
The height...
Hi guys, i want to lower my car more but unless im doing something wrong i appear to be at the bottom of my coilover adjustment (apex comfys)
They have 200mm springs when unloaded, ive got them...
Sounds good to me, assuming the date is good for me I'm in.
Exactly my point, so it would be sucking in extra air after the AFM, therefore it would be lean?
Plug gaps are .7mm
What's the suggested method of hooking up a compressor?
It is over fuelling at idle, but I can't see why a boost leak off boost would cause it to run rich? As I'm not going to be loosing air as...
Oh right, just going by what my boost gauge reads. Will get it smoke tested t
In that case.
Be strange if it is a cracked core though, its been fine for months. Changed the plugs last week and...
Cleaned AFM, it runs the same with lambda connected and disconnected, ive just re done all my i/c pipe work but im getting about 17psi of vaccume at idle so it cant be a big leak.
Anything else i...
Hi all, my car is turning its grade 7 plugs black, to a point where they won't spark properly any more. Iv'e read this can be from running too cold plugs, im going to put some 6's in to see if that...
Hi guys, my SR is over fuelling badly at idle/off boost. I don't know what it does on boost as iv'e not tried to drive it hard in this condition. It seems ok from cold, but after a few minutes at...
I think he means the rear calipers he wants aren't compatible with cable handbrakes.
You could use z32/skyline hubs with the drum brake?
If I recall correctly a hydro handbrake won't pass a legitimate mot, if that's a concern for you.