Search:

Type: Posts; User: s200rat

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    1
    Views
    183

    every engine ive built the bearing tabs / notch...

    every engine ive built the bearing tabs / notch go on the same side.
  2. Replies
    10
    Views
    311

    it must be pretty flimsy steel work at that price...

    it must be pretty flimsy steel work at that price or there is hidden costs. Ive put up a few cold rolled metal section sheds and you would be ~3k for a kit of a shed that size + cost of the base...
  3. Replies
    38
    Views
    24,312

    Personally not used a PFC with the VW coils but...

    Personally not used a PFC with the VW coils but cant see any issue, really all the ECU is doing is triggering the coil by switching to/from earth. both Nissan and the VW coils use an ignitor amp to...
  4. Replies
    38
    Views
    24,312

    That is an odd one - the cams aren't extreme so...

    That is an odd one - the cams aren't extreme so shouldn't effect cold starts. and R8 coils should only improve the spark.

    do you have any more info on the car? i.e. what mods/state of tune as I...
  5. Replies
    1
    Views
    153

    Depending on what you want to achieve you could...

    Depending on what you want to achieve you could cut the fuel pump relay signal wire from the ecu and put a switch in that. ECU is in passenger foot well so running wires to dash shouldn't be tricky....
  6. Replies
    14
    Views
    512

    This would point to the bearing between input and...

    This would point to the bearing between input and mainshaft
  7. Replies
    14
    Views
    512

    im sorry to say but I would say its either input...

    im sorry to say but I would say its either input shaft bearing or mainshaft bearing in the gearbox. Do you have gearbox rebuild info with confirmation of what bearings and tolerance checks they done?...
  8. Replies
    38
    Views
    24,312

    How rough is the idle with the cams as the longer...

    How rough is the idle with the cams as the longer duration will effect it slightly but not greatly. The coils should not effect it so you must have an underlying issue. If idle was good prior to...
  9. Replies
    8
    Views
    271

    At idle with no load the ECU will be requesting...

    At idle with no load the ECU will be requesting the following timing ;) so yep interpolate these cells and your in the range that's being seen.

    Load = 7
    25deg @ 800rpm
    33deg @ 1200rpm

    Load 13...
  10. Replies
    8
    Views
    271

    Also watch out if your taking the timing signal...

    Also watch out if your taking the timing signal via the service loop at the back of the engine - ive never had good success with this.
    Best to use a normal HT lead stuck into the bottom of coil 1...
  11. Replies
    8
    Views
    271

    how are you timing it? I assume with a timing...

    how are you timing it? I assume with a timing light and where are you taking the trigger from?

    you say that it is off by 4-5marks and guess its -35deg but that doesn't sound right - the sr20 crank...
  12. Replies
    22
    Views
    3,513

    Sticky: a bit of info on the vag coils here as well....

    a bit of info on the vag coils here as well. https://www.sxoc.com/vbb/showthread.php?584905-A-quick-how-to-use-VAG-coil-on-SR20&highlight=

    However ive read the 350z coils also fit and have started...
  13. Replies
    7
    Views
    302

    ill PM you

    ill PM you
  14. Replies
    7
    Views
    302

    if your desperate for a top mount set up i'll...

    if your desperate for a top mount set up i'll sell you mine.
    full mazworx top mount set up with a gt3076, oil lines, down pipe..... easily +450hp set up.
  15. Replies
    7
    Views
    302

    if your planning on gt2871 or the 3071 then there...

    if your planning on gt2871 or the 3071 then there is no need to top mount. both fit with a low mount manifold and save you the hassle. a GT3071 will get you over 400hp.
    To be honest even for big...
  16. Replies
    4
    Views
    297

    the WhatsApp pictures have all ready started......

    the WhatsApp pictures have all ready started...
    got this in the morning.

    https://i.postimg.cc/SKRKxRjt/IMG-20190125-WA0000.jpg
  17. its not ideal due to galvanic corrosion. it will...

    its not ideal due to galvanic corrosion. it will cause the carbon steel around it will corrode faster.
  18. Replies
    16
    Views
    488

    White walls to enhance the light. Floors I always...

    White walls to enhance the light. Floors I always avoid grey as it hides bolts!

    Guess the most important thing is use a good 2k floor paint. Wall can be cheap masonry but the floor needs decent...
  19. Replies
    4
    Views
    3,001

    [QUOTE=brapbeard;6804687] I've been keeping an...

    [QUOTE=brapbeard;6804687]
    I've been keeping an eye out for the past few months for a good candidate but there's just nothing up in the area, they're all down in Englandshire and I work a lot and I...
  20. Replies
    7
    Views
    765

    I think I bought a rear black bumper off you a...

    I think I bought a rear black bumper off you a good while back ;)
    If so it's still living on in my 200sx.

    I'm fortwilliam ways instead of Aberdeen now. Passed a green s14a through Elgin a week...
  21. Replies
    8
    Views
    267

    Use some nordlock washers. Itll hold fine after...

    Use some nordlock washers. Itll hold fine after that.
  22. Don't get me wrong, I like s-body's as much as...

    Don't get me wrong, I like s-body's as much as most here but as an investment I don't think its a wise move. If you like sil80's just buy a 180 that's been converted. You will be lucky to break even...
  23. Replies
    38
    Views
    24,312

    Awesome you have access to a scope! Your graphs...

    Awesome you have access to a scope! Your graphs are supporting the cause being excessive charge / dwell so I would say it's worth knocking the time down to 1.8 as a starting point.
  24. Replies
    38
    Views
    24,312

    What ECU do you have? I don't have access to my...

    What ECU do you have?
    I don't have access to my laptop to check the base map for the r34 but I remember the dwell time is higher than the Sr for the ignition.

    Think it's over 2.0ms whereas for a...
  25. Replies
    2
    Views
    686

    If you have a mothercare shop or any baby shop...

    If you have a mothercare shop or any baby shop that sells prams ask them ;)
    Generally people buy direct from shop floor and don't want the boxes. They're strong and large
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4