Search:

Type: Posts; User: green_rs13

Page 1 of 20 1 2 3 4

Search: Search took 0.38 seconds.

  1. im pretty sure a 2 pence piece is the right size...

    im pretty sure a 2 pence piece is the right size to blank it off on the exhaust mainifold side.
  2. Replies
    9
    Views
    96

    i think i might have a pair of new old stock OEM...

    i think i might have a pair of new old stock OEM ones.
    how much of a rush are you in?
  3. Replies
    1
    Views
    91

    i always jack them on the tie down points on the...

    i always jack them on the tie down points on the front radiator support panel
  4. Replies
    7
    Views
    168

    you are ok to connect those bits together. id...

    you are ok to connect those bits together.

    id always use 20/50 fully synth in my old CA so i doubt its a viscosity issue. probably have some air in them.
  5. Replies
    4
    Views
    148

    i had a dakota box ruuning off a front abs sensor...

    i had a dakota box ruuning off a front abs sensor and could never get the speedo to be accurate across the entire speed range.
  6. Replies
    3
    Views
    129

    its the same car underneath so, yes.but some...

    its the same car underneath so, yes.but some people have reported japspeed ones make a weird duck like noise.
  7. Replies
    4
    Views
    131

    when you have the rear discs off run a grinder...

    when you have the rear discs off run a grinder around the bits that need cutting off.

    just swap the calipers and the discs for the rear.

    make sure you have the z32 front caliper mounting bolts.
  8. Replies
    118
    Views
    35,892

    you missed the part where you put 10 tonnes of...

    you missed the part where you put 10 tonnes of copperslip on the threads.
  9. Replies
    7
    Views
    130

    drill the threads out and put a nut behind it if...

    drill the threads out and put a nut behind it if you can get access.
  10. i seen a 240z being restored once and they built...

    i seen a 240z being restored once and they built 2 big wooden picture frame squares, bolted them to the subframe mounting points and rolled it onto its side. (picture the car being encapsulated...
  11. tack weld a length of box section to each chassis...

    tack weld a length of box section to each chassis rail and cut them off when your done. keep the doors closed.
  12. do they go down if you wind them a little bit?

    do they go down if you wind them a little bit?
  13. i always jack the front of the cars up on the...

    i always jack the front of the cars up on the towing eyes either side of the radiator support panel.if you have a decent jack take the spinney pad thing off and the tow hook fits nicely in the top of...
  14. Replies
    6
    Views
    187

    just stick a blob of weld on the nuts after its...

    just stick a blob of weld on the nuts after its been setup.
  15. Replies
    9
    Views
    303

    what height are the guides? ive heard of people...

    what height are the guides? ive heard of people using guides in both sides instead of a shim and a guide.
  16. Replies
    9
    Views
    303

    any decent machine shop will have a surface...

    any decent machine shop will have a surface grinder that can resize your shims
  17. Replies
    23
    Views
    853

    are they just going to strip the areas they need...

    are they just going to strip the areas they need to work on then recoat the entire floor pan to match? as that is well different to media blasting the entire underside.

    the whole interior would...
  18. Replies
    23
    Views
    853

    glad im pretty handy at this sort of stuff now i...

    glad im pretty handy at this sort of stuff now i know how much it costs.

    i had mine blasted and ended up doing rear pockets and the backs of the sills and the usual spots.
  19. Replies
    23
    Views
    853

    SR autobodies.

    SR autobodies.
  20. Replies
    4
    Views
    198

    its pretty straight forward, although i would...

    its pretty straight forward, although i would stick a VVT engine in TBH unless i already had the other engine.
  21. Replies
    4
    Views
    260

    try a place called 'Sumpscuffers' who are up in...

    try a place called 'Sumpscuffers' who are up in derby. they are well versed in welding up old S-chassis.
  22. Replies
    8
    Views
    284

    s14 lower arms don't fit s13 subframes. tbh...

    s14 lower arms don't fit s13 subframes.

    tbh the s14 subframe has better anti squat properties than the s13 so I would just sell your s13 stuff and fit s14
  23. Replies
    2
    Views
    142

    behind the passenger side strut is a brown box....

    behind the passenger side strut is a brown box. this is the wiper control box, check its not full of water and the plug is in decent condition.
  24. I used the VAG coils, I figured every motor...

    I used the VAG coils, I figured every motor factor in the country would have a spare coilpack on the shelf if I was out and about and needed to buy 1 urgently. I bought the connectors from the VEMS...
  25. Replies
    1
    Views
    105

    stock rb25 shifter is longer after the pivot ball...

    stock rb25 shifter is longer after the pivot ball part of the shifter.

    SR is the same as the CA (as its the same box)

    some short shifter kits have an additional bit that bolts over the big...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4