Search:

Type: Posts; User: hooky

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    329

    The old school GT2871r (.86) will probably get to...

    The old school GT2871r (.86) will probably get to your power goals, but it will be annoyingly laggy, Particularly on a Non-VVT SR..

    Either of the GTX series would be like a 'Night & Day'...
  2. Replies
    9
    Views
    329

    The GTX2871r seems a bit of an oddball mismatch...

    The GTX2871r seems a bit of an oddball mismatch TBH, The Compressor side is easily capable of flowing well over 500Hp but its mated to a T28 Turbine that will realistically top out in the low 400hp...
  3. Replies
    1
    Views
    79

    The GTX series has a massively improved...

    The GTX series has a massively improved Compressor wheel, it'll probably yield as much as 100hp more than the old 'Disco potato' Gt2860rs with probably slightly less lag!
    Turbo technology has...
  4. Thread: Headgasket help

    by hooky
    Replies
    4
    Views
    167

    Can you post a video of the leak? if its coming...

    Can you post a video of the leak? if its coming out from above the water pump its most likely just the pump gasket. Your Head gasket is probably fine...
  5. Replies
    24
    Views
    562

    double post ....

    double post ....
  6. Replies
    24
    Views
    562

    Looking at the old SXOC post (referenced above)...

    Looking at the old SXOC post (referenced above) it looks like the two shafts pictured left & right are what you need, but your old one in the middle looks suspiciously like the one on the left?
    ...
  7. Replies
    24
    Views
    562

    Night mare....i had no idea the EU & JDM carriers...

    Night mare....i had no idea the EU & JDM carriers were different. That's some pretty poor service from RHD to be honest :(

    I'm Curious, could you use the shorter of your Original shafts with the...
  8. Replies
    11
    Views
    306

    Yes, Toys and Hobbies i have... Its money that...

    Yes, Toys and Hobbies i have... Its money that i'm always needing more of! :D
  9. Replies
    11
    Views
    306

    Also, will there be the same level of 'Nostalgia'...

    Also, will there be the same level of 'Nostalgia' for homologation cars in twenty or thirty years?

    After all, the people who are currently buying and acquiring the 80's icons are the very people...
  10. Replies
    11
    Views
    306

    Yaris GR as an investment?

    I truly believe that this is one of the most exciting affordable cars to come onto the market for many decades, and seems like a no-brainer investment car. Iím sorely tempted to order one, maybe put...
  11. Being a Reflector scope, you get a lot of tube...

    Being a Reflector scope, you get a lot of tube for your money, However, the sky's the limit when you start adding some quality eyepieces (pardon the pun) ....:eek:




    TBH i do have a camera...
  12. with the 'working from home' meaning late nights...

    with the 'working from home' meaning late nights are plentiful, i came good with my promise to my kids with a new scope... they'll love it when they can reach it! :D


    <blockquote...
  13. Replies
    24
    Views
    562

    When Nissan developed the VLSD they just used a...

    When Nissan developed the VLSD they just used a standard open diff and found some space to squeeze in the Viscous coupling. This required extending one of the half-shafts so that both shafts could...
  14. Replies
    2
    Views
    75

    Does it have a Stainless steel exhaust housing?...

    Does it have a Stainless steel exhaust housing? if so Then welding to it should be ok, but if it is has a cast iron housing it'll be a world of pain....
  15. I would say the GTX2860r Gen 2 would be more...

    I would say the GTX2860r Gen 2 would be more suitable for a target of 320hp (and still a little tinkering room left).
    A new set of OEM coils is only good for a stock boost engine, There are a few...
  16. Replies
    12
    Views
    417

    if its clutch/flywheel related, then putting...

    if its clutch/flywheel related, then putting pressure on the clutch pedal should change/eliminate the noise....
  17. What ever that was that was rattling around was...

    What ever that was that was rattling around was significantly heavy to make those holes! have you checked the turbine wheel on the turbo?
    In all honesty, if you were leaving the engine completely...
  18. Replies
    11
    Views
    387

    possibly, but they are pretty strong. One...

    possibly, but they are pretty strong.

    One thing you can check is that the slave cylinder is not 'Bottomed out'. You should be able to push the piston back a few millimetres, if this is bottomed...
  19. Replies
    11
    Views
    387

    Are you using the correct release bearing? maybe...

    Are you using the correct release bearing? maybe its too long and constantly pressing the release springs?
  20. Replies
    4
    Views
    225

    Its either a coil pack or the plug gaps need...

    Its either a coil pack or the plug gaps need closing up.
    Coil packs are a very common failure.
  21. Replies
    249
    Views
    56,429

    Thats just pulls harder and harder! :eek: I'm...

    Thats just pulls harder and harder! :eek:

    I'm a little confused by the graphs though, are they overlays of different pulls at different boost levels?
    The lowest graph revs out to 7k but the...
  22. Replies
    12
    Views
    453

    I think the Greddy offerings for the 25G are 8,10...

    I think the Greddy offerings for the 25G are 8,10 & 16.....
    Our little 2ltr four bangers dont really flow enough gas at low RPMs for anything but the 8cm .....Although the cams will help as they'll...
  23. Replies
    22
    Views
    806

    So the ECU is s14a but the plug & loom are s14? ...

    So the ECU is s14a but the plug & loom are s14?
    If so there will be a few wires that require re-locating in the plug.
  24. Replies
    22
    Views
    806

    Have you only changed the Engine loom? i know the...

    Have you only changed the Engine loom? i know the The s14 & s14a ECU pinouts are slightly different. A bit of googling should bring up the diagrams. if i recall there are only 2 or 3 wires that go to...
  25. Replies
    20
    Views
    878

    It can't be the CAS if it fires with Easystart,...

    It can't be the CAS if it fires with Easystart, so must be injector related (assuming you have pressure at the rail).
    You should have a constant 12V at the injector when ignition on, so check this...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4