Hi scottish, Do not attempt to switch on your pc or power up that power supply unit if you believe its failed, Especially if its starting to smell, You could risk burning out your motherboard and or...
Type: Posts; User: R1PE
Hi scottish, Do not attempt to switch on your pc or power up that power supply unit if you believe its failed, Especially if its starting to smell, You could risk burning out your motherboard and or...
Ive owned the 6-750 and thousand gsrx, The 750 was perfect for everyday hooning, The Thou was perfect for commutes and general grin factor, Although that may be because i had a quick action throttle...
Maybe a daft question but is the diff in these LSD'S?
Ahhh, i suppose this is surplus to requirements now then, Ill disconnect.
Cheers bud
Hi guys, On the passenger side wheel arch there is some sort of sensor block fitted as standard, This wasnt fitted in my old manual s14a? is this something to do with the auto gearbox?.
I carried...
Neutral position /inhibitor switch pin 35 is what the s14/s14a pinout guide in the useful threads section suggest on the ecu, yet the auto to manual guide for wiring says for wiring to use the 3rd...
Cheers guys
Oh well thats good news, saves me cutting into ecu loom any more :).
I think i was getting confused with the speed sensor thinking it was a 5th position sensor, Using that 240sx auto to manual wiring conversion site, There was no mention of a speed sensor just...
s tthe 5th position switch vital at all? Just about to wire in my neutral position and reverse lights but the 5th position switch on multimeter has no change in resistance regardless of what gear im...
"The Reason That You Do Not Connect The 5th Position Switch Harness To The Transmission At This Time Is That The ECM Is Different For Automatic Transmission And Manual Transmission Cars. Pin 7...
Forgot to mention I have the manual transmission loom too, spliced about halfway down by where it meets by steering rack
Hey guys, Ive seen the link posted http://www.ka24development.com/cwilfert/S14_tranny_swap_electrical.html#starting system and found it very helpful. My question though is, I will be fitting this...
Hey guys, how much would you charge to carry out this conversion if i supply all the parts needed with the bulkhead holes drilled etc
Also yes the nats is removed :) could this be why shes flashing
To be clear because i tend to rush writing on this using a useless touch screen phone
Stage 3a kit has been fitted
Manual ecu runs the car ok, getting the stage 3a chip swapped over to the auto ecu...
Forgot to mention, as soon as I've sourced a gearbox ill be converting vehicle to a manual as i have everything needed bar a gearbox lol
Hi guys, I've finally finished swapping over all my stage 3a kit to this auto and fitted the stage 3a chipped ecu, vehicle runs ok etc yet engine light is flashing? Any ideas?
Ah sweet so basically block both pipes secure and then i can bang on the non egr inlet on. Cheers guys :)
Hi guys, am in the process of swapping allot of stuff over from my spare engine, removed the egr completly, planned on replacing the inlet manifold to the one from my manual non egr engine, once i...
Also I've fitted uprated fuel pump too Incase she ran risk of running lean
Ahh is it ok to pootle around in if driven gently as it seems to idle and run nice on the z32? I have gt2871 and 555 injectors + spare ecu with stage 3a setup on it to be fitted at some point, just...
Just a quickie guys, my standard afm in my new s14a auto is playing up, can i wire in z32 and will it be safe to run or require remap?
Hi guys, ive read the guides on auto to manual conversions on here, One question i have though, is there much of a difference between the auto and manual prop shafts?
Also if anyone has any parts...
Hi guys what plugs do you use on your stage 3a setups or what would you suggest, im running ngk 8's and due a change, would this be a suitable grade for a car that is given death on regular...