Hey guys, I have a VLSD, when I brought the one from previous owner, he told me it will fit the S13(CA), but he also said it was off a s14, so anyone can tell me how to tell if it is a S13 or S14?
...
Type: Posts; User: roja
Hey guys, I have a VLSD, when I brought the one from previous owner, he told me it will fit the S13(CA), but he also said it was off a s14, so anyone can tell me how to tell if it is a S13 or S14?
...
wow, that is a lot to remove. Let me check for the belt first, think martinbattye is right, the oil looks like it has been there for a while, as long as the belt is ok, will not change the seal. will...
Thanks martinbattye, will inspect cambelt, but still wonder if want to change the camshaft front seal, do I need to take off the rocker cover to do it? anyone knows? cheers
thanks guys, i was reading the manual, and wonder do i need to take off the top rocker cover to get the cam shaft seal replaced???
Hi, guys, top up oil about a month ago, checked today, oil run low, so top up with 500ml 15w-50. and notice there is grease/dirty oil around the gap of the upper and lower front cambelt cover, is it...
thanks man, will give him a call. is his name Enigma?
cheers
guys, thanks for all your input. the dump valve i am planning to install is a Greddy one, which can be used as an recirc dump valve, but i am using a hard pipe which is one 45 degree silicone hose +...
guy, don't ask why i need a dump valve, i can assume you it is not for the sound. We all know the a/f ratio will be rich, so i am thinking using an apexi Neo to correct that. Had a look at the manual...
hi guys, i have one of these sterling transponder tag with my alarm system, the little glass looking-thingy in the tag is a bit broken, it still works. Just think it is nice to have a spare one,...
thanks man, will try that
anyone??
Guys, I need your advices again. Few months ago, when I was trying to sort out the unstable idle issue, I noticed some kind of tractor/rusty bearing/wear out belt noise from alternator area, so I...
using standard 4 studs hub with z32 front brake, can't find any 5mm spacer, anyone could point the right direction?
cheers
Hi Guys, I am planning to take off my T28r turbo tomorrow, it is on standard manifold and turbo elbow. I understand that it will be easier to take the manifold altogether with it. I had a look at it...
Troy, thanks man for your help and advice, i will make a note about the bung. Think amybe buying one see how it goes. will let your know if i need the ECV, again, thanks a lot.
FULLER, i am sure...
Thanks New200guy, dan23, shogun, MrPARR and TrIcK^, I will just start the car and just go easy, thanks for all your comments again. I still wonder if there is any place i can find some kind of...
Thanks for everyone's comments again.
Troy, did you mean using a bung may damage the turbo?
Si-PS13, will try to pm STEVE A, and ask him about it, I think apex is selling that ECV.
shogun,...
Many thanks for everyone on the post. for the apexi active control valve, doesn't it affect performance???
i mean it looks like it can be fully closed.
many thanks
Si-PS13, that looks good, but very dear. i am thinking about...
xR33, when you say "hammer it", what does it man??? thanks
Thanks Markturbo, and voodoo_melon, thanks very much for all your help.
Thanks voodoo_melon for your comment. I am depressed, thinking about selling the car now. I really don't want to cause any troubles to anyone at all. I wonder if you are suggesting that i can just...
I am a bit upset at the moment, got complain from neighbor again about noise when running the engine when the car is at stationary. I only did it to warm the car up and cool the turbo down. Now my...
NesjeX, I think someone said on here, the RET MTR relay is something to do with the pop-up light, do you have mod like lazy eye or something?
guys, i am confused. M6 didn't fit. and looking in service manual, can't find anywhere talking about the size and length of that bolt, plz help!!!