Search:

Type: Posts; User: 6terras

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    90

    Blowing fuses is not going to be an issue as i...

    Blowing fuses is not going to be an issue as i will feed them with a relay.
    I am tempted to fit one side with a 55w setup and monitor the bulb temps over 15 minutes to see if there is much...
  2. Replies
    3
    Views
    90

    Will 55W HIDs melt the s14a projector?

    Its MOT time next week and my current 35W HIDs are playing up. I have a spare brand new set of 55W HIDs that i can fit but i am a bit worried about melting the headlight inners.

    Trying to decide,...
  3. Thread: Black beasty

    by 6terras
    Replies
    955
    Views
    247,653

    no worries

    no worries
  4. Thread: Black beasty

    by 6terras
    Replies
    955
    Views
    247,653

    Glad you got it sorted!

    Glad you got it sorted!
  5. Replies
    6
    Views
    127

    I think i just got lucky with LED and resistor...

    I think i just got lucky with LED and resistor selection. I baught small 3mm clears. (I repair PCBs for a living). Cant find any more info on my email account

    And yea... you dont want them too...
  6. Replies
    6
    Views
    127

    The bulbs in the cluster are just 501 wedge...

    The bulbs in the cluster are just 501 wedge bulbs.
    If your talking about others like switch LEDs, i have done them all. I bought a pack of white LEDs with matching resistors and got them done. If...
  7. Thread: Black beasty

    by 6terras
    Replies
    955
    Views
    247,653

    Looking good! Clocks still working?

    Looking good!

    Clocks still working?
  8. Ready and waiting, iron in hand.:wave:

    Ready and waiting, iron in hand.:wave:
  9. Thread: Rev counter

    by 6terras
    Replies
    7
    Views
    261

    well done!

    well done!
  10. Thread: Rev counter

    by 6terras
    Replies
    7
    Views
    261

    Thats why i asked if the entire pcb was reflowed....

    Thats why i asked if the entire pcb was reflowed.

    I am a professional pcb reworker. I was also a soldering teacher to aerospace standards for 6 years. If you want you can send it to me. I have...
  11. Thread: Rev counter

    by 6terras
    Replies
    7
    Views
    261

    HI. I have fixed lots of these by removing all...

    HI. I have fixed lots of these by removing all the old solder and adding fresh leaded in its place. Have you refolwed the entire pcb?
  12. Got mine yesterday. Thank you!!!

    Got mine yesterday. Thank you!!!
  13. Replies
    10
    Views
    886

    i got some buttons from an old cobra key fob a...

    i got some buttons from an old cobra key fob a few years back. there was some on ebay like this one

    https://www.ebay.co.uk/itm/255043685620?hash=item3b61c9ccf4:g:nQMAAOSwfK5fx8YT

    But as stated...
  14. The bracket, 3rd picture down. i had one of these...

    The bracket, 3rd picture down. i had one of these left over after my auto to manual conversion. i believe it held some of the gearbox loom.
  15. Replies
    5
    Views
    226

    I have done a conversion myself. The first pic is...

    I have done a conversion myself. The first pic is where the auto looms plug to. I had a manual loom but still had to use them sockets for the reverse and the old auto neutral sensor. The connector...
  16. orders in!

    orders in!
  17. Replies
    2
    Views
    178

    Hi. Not done it myself but a competent garage did...

    Hi. Not done it myself but a competent garage did it. Heres a link to what they did. You’ve probably seen it all before.
    ...
  18. Replies
    5
    Views
    188

    https://uploads.tapatalk-cdn.com/20211120/d7b887e4...

    https://uploads.tapatalk-cdn.com/20211120/d7b887e48a456943ee25348609812272.jpg


    Sent from my iPhone using Tapatalk
  19. Replies
    5
    Views
    188

    I didnt have holes but did similar to the rear...

    I didnt have holes but did similar to the rear pannel. Did you take off the rubber boot seal? The lip it sits on was rotten on mine, in the middle near the latch.
  20. Replies
    11
    Views
    776

    Thanks. i wish i had done the underseal when i...

    Thanks. i wish i had done the underseal when i baught the car. better late than never i suppose. all the rust that has come through since has come from inside out.
  21. Replies
    11
    Views
    776

    Every 200sx owner need this…… ...

    Every 200sx owner need this……

    https://uploads.tapatalk-cdn.com/20211116/30f818badd87ddad78973fc05166a6d2.jpg
    A de-rusting kit[emoji1360]


    Sent from my iPhone using Tapatalk
  22. Replies
    11
    Views
    776

    Thanks. Mite change them one day but i like the...

    Thanks. Mite change them one day but i like the simplicity and cheep tyres.
  23. Replies
    11
    Views
    776

    cheers Markcro.

    cheers Markcro.
  24. Replies
    11
    Views
    776

    Baught myself some nismo s-tunes this year....

    Baught myself some nismo s-tunes this year. Needed a clean up……
    https://uploads.tapatalk-cdn.com/20211116/e7a0aaf9807a3f0d765ce27fb6ded3b6.jpg
    ...
  25. Replies
    11
    Views
    776

    https://uploads.tapatalk-cdn.com/20211116/98e01e9c...

    https://uploads.tapatalk-cdn.com/20211116/98e01e9c03f7f05a921fc9ae525b791f.jpg

    https://uploads.tapatalk-cdn.com/20211116/a1bee8fc69ba13637c6df7fa47b457df.jpg
    ...
Results 1 to 25 of 206
Page 1 of 9 1 2 3 4