Search:

Type: Posts; User: markcro

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    9
    Views
    149

    I will try to check later. But from memory the...

    I will try to check later. But from memory the bottom ones look like the stops (just upside down) on the radiator cross member, the middle ones are the ones at the shock turrets that I was talking...
  2. Thread: part id

    by markcro
    Replies
    5
    Views
    120

    That is one clean underside! Very nice! :-)

    That is one clean underside! Very nice! :-)
  3. Replies
    9
    Views
    149

    I never bought these myself, but I have been...

    I never bought these myself, but I have been noting down any part numbers that I have seen listed over the years for my future reference. But I think that there is a little stop on the actual front...
  4. Replies
    9
    Views
    149

    This is what I noted down a few years back. I...

    This is what I noted down a few years back. I actually need some as well.


    65823-28E00 middle on turret.
    65822-M7000 are on headlamp motor brackets
    62840-D0100 at front corners. The rubber...
  5. Replies
    6
    Views
    112

    Thanks guys

    Thanks guys
  6. Replies
    6
    Views
    112

    What was the part number for the clips and where...

    What was the part number for the clips and where did you get them? I may need to replace a few.
    Cheers.
  7. Replies
    414
    Views
    48,097

    38mm is about my limit for size. Most of my...

    38mm is about my limit for size. Most of my watches are 36mm. But 40mm is not too bad, I could probably manage that size. Definitely not kitchen wall clock territory. Very nice watch!
  8. Replies
    414
    Views
    48,097

    Woo I like that! Nice watch! What size case is...

    Woo I like that! Nice watch! What size case is it?
  9. Replies
    7
    Views
    166

    Blue. Pink is for girls! ;-) I've always stuck...

    Blue. Pink is for girls! ;-)
    I've always stuck with the standard gycol blue.
  10. Replies
    20
    Views
    250

    I stopped using them as the Yellowstuff pads come...

    I stopped using them as the Yellowstuff pads come with a backing already in place and as you found, there it very little room to get these in, so I left them out.
  11. Replies
    20
    Views
    250

    Yes the are. The GTST and SX calipers are...

    Yes the are. The GTST and SX calipers are practically identical.. The only real difference being that the SX calipers are cast iron and the GTST ones are alloy.
  12. Replies
    20
    Views
    250

    Then it could be just sh1t pads. Change them and...

    Then it could be just sh1t pads. Change them and let us know. And also, all pads need bedding in. So the new pads will get better and better with use.

    As a side note, a mate of mine has a Beemer...
  13. Replies
    20
    Views
    250

    If bad then yes. But if it's just one piston out...

    If bad then yes. But if it's just one piston out of 4, then maybe not. Have you check each piston individually? Including the rears? The should extend and then push back in smoothly and easily. And...
  14. Replies
    20
    Views
    250

    I would bet that you have a sticky caliper. Even...

    I would bet that you have a sticky caliper. Even the standard fully working SX brakes are pretty good (no matter what people say). I used for a few years standard pads, Ferrodo 2500s, EBC Redstuff...
  15. Replies
    10
    Views
    200

    Just looking at the price of things now! Wow! For...

    Just looking at the price of things now! Wow! For example, from memory Hardrace rear droplinks were about 15 quid back in the day. And so I have two sets of brand new ones in my shed as they were...
  16. Replies
    13
    Views
    285

    And yes, get all the welding done at the same...

    And yes, get all the welding done at the same time as it work out cheaper.
  17. Replies
    13
    Views
    285

    "they normally would only do mot style repairs...

    "they normally would only do mot style repairs "........... that would worry me alot to be honest. No good having photos after the job is done. Get them to keep you updated. I.e. no patches over bad...
  18. Replies
    10
    Views
    200

    I replaced some rear suspension arms and shocks...

    I replaced some rear suspension arms and shocks etc. with after markets ones which came painted in lovely metallic silver, purple and red paint finish/ They were very nicely painted. But the first...
  19. Replies
    8
    Views
    530

    Are you mad? That emoji is too violent! ;-)

    Are you mad? That emoji is too violent! ;-)
  20. Thread: High idle

    by markcro
    Replies
    4
    Views
    113

    Vacuum leak somewhere? Mine started idling high...

    Vacuum leak somewhere? Mine started idling high one morning as the pipe to the boost pressure sensor had come loose
  21. Thread: New pc time

    by markcro
    Replies
    21
    Views
    349

    You bastar'd! That comeback made me spit out my...

    You bastar'd! That comeback made me spit out my tea!! :D
  22. Replies
    4
    Views
    173

    I have R33 fronts on a 330mm big brake kit and...

    I have R33 fronts on a 330mm big brake kit and R33 rears and I kept the standard master cylinder (BM50). I have never driven one with the BM57 but never found the standard to be lacking so never...
  23. Replies
    13
    Views
    316

    What are the pros and cons of a one piece?

    What are the pros and cons of a one piece?
  24. Replies
    17
    Views
    723

    Nice S14! But wow!You've had some list of dream...

    Nice S14! But wow!You've had some list of dream cars!
  25. Replies
    6
    Views
    84

    Just go around all 4 corners starting with the...

    Just go around all 4 corners starting with the furthest corner from the brake servo and you should be fine. I take it that you closed the bleed nipples on the calipers?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4