Search:

Type: Posts; User: diamondsink

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds; generated 33 minute(s) ago.

  1. Replies
    67
    Views
    8,261

    After the bottom end was gone the first time did...

    After the bottom end was gone the first time did you even clean the block before rebuilding it. All that shite will be in the oil ways, pump, etc. The whole engine and all the components needs acid...
  2. I have geomasters and run the car low (tyre...

    I have geomasters and run the car low (tyre tucked) . Ive not have any problems with the drive shafts even though the internet says you will. I did grind a scallop out the traction arm fork to clear...
  3. Replies
    343
    Views
    57,614

    Lovely work, you do a tidy job. Refreshing to see...

    Lovely work, you do a tidy job. Refreshing to see it done so nicely.
  4. Replies
    7
    Views
    2,318

    Would be good idea to have them tested, they look...

    Would be good idea to have them tested, they look pretty clean but its always worth it with unknown secondhand injectors. Would show you what they are too.
  5. Replies
    40
    Views
    3,944

    Iv tried loads of oil in both SR and Z32 boxes...

    Iv tried loads of oil in both SR and Z32 boxes including expensive MT90 etc. Ended up going with Motul Technosynthese, good with noisey hard to shift boxes.
    ...
  6. Replies
    5
    Views
    907

    Think i can see day light through your rear...

    Think i can see day light through your rear quarter.
  7. Replies
    4
    Views
    316

    Nissan is really your best bet, but someone like...

    Nissan is really your best bet, but someone like Conceptua tuning or JDM garage might have some. Make sure they are OEM quality, don't buy cheap ones
  8. Replies
    18
    Views
    1,025

    I run a CA18 filter on my TRUST plate. Its nice...

    I run a CA18 filter on my TRUST plate. Its nice and big too (more filtration area was my thinking)
  9. Replies
    18
    Views
    1,333

    Shame they didnt sort the short oil pump drive on...

    Shame they didnt sort the short oil pump drive on the crank though.
  10. Id give the ebay joints about 3-6 month before...

    Id give the ebay joints about 3-6 month before they are rusted sloppy scrap.
  11. Replies
    6
    Views
    343

    The oil would have to be crazy low like none to...

    The oil would have to be crazy low like none to starve the pickup. Definitely not even on the dip stick. The sensor is one wire which earths when the pressure is low (under 5psi i think). Check the...
  12. Look the same as the Apex rods.

    Look the same as the Apex rods.
  13. Replies
    7
    Views
    431

    Pretty surre they are

    Pretty surre they are
  14. Replies
    15
    Views
    734

    Tein, the japspeed joint will last around 5...

    Tein, the japspeed joint will last around 5 minutes.
  15. Replies
    4
    Views
    386

    bolt removal!! A 19mm socket and turn...

    bolt removal!! A 19mm socket and turn anticlockwise. I'd find a better garage if they cant even manage that.
  16. Replies
    38
    Views
    53,785

    Real nice write up, always thought about doing...

    Real nice write up, always thought about doing thi but never really looked into it. Actually looks like a simple job as long as you good at soldering and loom making.

    So is this the NGK Audi R8...
  17. Replies
    2,553
    Views
    684,975

    Just wind the stud out to match. Its will just be...

    Just wind the stud out to match. Its will just be a slight difference in the block.
  18. 1.2mm to keep the same comp ratio. Lots of people...

    1.2mm to keep the same comp ratio. Lots of people want to lower their C/R. I tried both lower and higher C/R, higher makes for a much better drive and response.
  19. Replies
    44
    Views
    1,824

    I made one with on old lifter and a DTI

    I made one with on old lifter and a DTI
  20. Replies
    9
    Views
    781

    A tube of Wellseal is your friend with a MLS....

    A tube of Wellseal is your friend with a MLS. http://www.wellseal.co.uk/
  21. Replies
    2
    Views
    251

    I never seen it or heard of it in my eight years...

    I never seen it or heard of it in my eight years of 200sx ownership. Not to say it doesn't happen. Id just be finding a secondhand gauge cluster and plugging it in.
  22. Replies
    343
    Views
    57,614

    Sweet car, looks very tidy and well keep. Reckon...

    Sweet car, looks very tidy and well keep. Reckon painting the intercooler black would look good.
  23. Intake pipe collapsing?

    Intake pipe collapsing?
  24. Replies
    3
    Views
    772

    People complain about speeding and dangerous...

    People complain about speeding and dangerous driving on the streets with drifting etc become popular but then want to shut down every venue for people to partake in their pleasures.

    Boils my...
  25. Replies
    9
    Views
    392

    Any SAE 100 R6 oil hose will be fine. stick some...

    Any SAE 100 R6 oil hose will be fine. stick some fire sleeve over it though
Results 1 to 25 of 494
Page 1 of 20 1 2 3 4