For anyone else looking at this later. The steering column grounds through the two bolts under the dash the attaches the column to a heavy metal bar that runs across the car under the dash.
Im...
Type: Posts; User: johnnyhillen
For anyone else looking at this later. The steering column grounds through the two bolts under the dash the attaches the column to a heavy metal bar that runs across the car under the dash.
Im...
Is that the bolts under the dash or is it in the engine bay
Sent from my LYA-L09 using Tapatalk
Im in the last stages of rebuilding my car and realised the horn didnt work. I think I have worked out that it should ground through the steering column but when I check with a multimeter the...
The H1 bulbs have only one pin. They ground through the body of the bulb.
Any hid kits I've seen just replace the standard H1 bulbs. If this is the case the standard H1 bulbs should slot in to a...
I think mine needs stripped and rebuilt with new solenoids but I wouldn't know where to start and I can't find anywhere that will do it. Most places won't even look at it.
Let me know how it goes...
I don't think it will pass mot with no abs unit. It's bound to show the abs light on the dash.
Sent from my LYA-L09 using Tapatalk
https://www.energysuspensionparts.com/
I got a full set from energy suspension. No complaints.
Sent from my LYA-L09 using Tapatalk
The long question is. I have had the abs unit off the s14 for quite a few years and when I fitted it and tried to bleed the brakes I found the fluid doesn't flow through to the rear brakes. I've done...
Hi
I'm refilling the car with brake fluid after amenities information years rebuilding the car. I was having issues getting the brake fluid to flow. Eventually got the fluid through the abs unit...
Got the radiator checked and there was lots of holes in it. Apparently its caused by corrosion after 5 years in my garage with no anti corrosion coolant to stop it. New mishimoto on the way
That's definitely the answer.
I'll probably get a new one eventually but I've already spent a load recently getting it back on the road so I'll see if I can get it fixed for now.
Hi everyone
I've just put my aluminium radiator back in my car after a long rebuild. Filled it with antifreeze and it's pissing out the bottom. :facepalm:
Im not happy to say the least. I was...
Thanks. Everything in the gearbox looks secure so must not be that important.
If found out the last one is the last bracket for the fuel lines before the reach the fuel filter. It's mounted...
I'll go through the inlet diagrams with a fine tooth comb again.
Thanks
I was thinking windscreen washer as well
I do intent to fit a radio so I'll try and figure out where it goes on the alternator.
I'm pretty sure the straight one is aftermarket so it will probably go into the bin
Hi
Im rebuilding my s14a but and im 90% done but i have 5 parts that I cant ID. They were all labelled at the time but I had to take the labels off to get them sandblasted and powdercoated and the...
I think your very close to the limit of the gearbox at 400.
Sent from my LYA-L09 using Tapatalk
I was working on an s14 but I'm sure the threads are the same. I struggled to get anything with the right threads as most were too course. I ended up buying a basic set and then having to buy...
That sounds interesting. I have a rollcage in my garage I'm planning on fitting soon. I wonder if these new rules apply in northern Ireland as well. I'm sure there's other aspects of it would make...
I think I'll change mine aswell from the reviews above. Is there any other BMC that work. I'm sure The bm57's are getting pretty rare. Can the BMC from a 350z be fitted?
Sent from my LYA-L09 using...
Changing the BMC only changes the distribution of brake force from front and rear. I think the bm57 send more to the rear cause on the z32 the rears are 2 pot compared to the standard 1 pot on the...
Also could you not just remove the turbo and down pipe as one and separate after
Sent from my LYA-L09 using Tapatalk
I haven't touched a standard downpipe in a while but I'm pretty sure at least one of them is a stud with a nut on it because it wasn't possible to use a bolt due to access. Not sure if that helps you...