Search:

Type: Posts; User: Mario

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    15
    Views
    701

    Yes Mike good call, thanks [emoji106] Sent...

    Yes Mike good call, thanks [emoji106]


    Sent from my iPhone using Tapatalk
  2. Replies
    15
    Views
    701

    Update. Took everything apart. Found there was...

    Update. Took everything apart. Found there was voltage going to the pumps, so not electrical. Found a lot of gunk in the reservoir so gave pumps a blast with wd40, air, a shake and tap and they freed...
  3. Replies
    15
    Views
    701

    Thanks for the reply Mike. There are separate...

    Thanks for the reply Mike. There are separate pumps for front and rear - it’s possible they’ve both failed I guess.


    Sent from my iPhone using Tapatalk
  4. Replies
    15
    Views
    701

    Washer jets not working

    Hi guys. Both front and rear washer jets have stopped working on my 14a. The wipers work fine, just not the jets.

    I can’t hear the jets buzz when activated, so I think it’s electrical. Are there...
  5. Replies
    20
    Views
    877

    Thread resurrection.... Need a new set of...

    Thread resurrection....

    Need a new set of tyres. Would appreciate peoples feedback on some of the tyres mentioned above, or any other suggestions.

    Have Falken 452s on mine and whilst they were...
  6. Replies
    5
    Views
    538

    Update, O2 sensor changed using crows foot...

    Update, O2 sensor changed using crows foot spanner (definitely the tool for the job), and went for a nice long drive before the test. Passed with flying colours, so another SX back on the road ;-)
  7. Replies
    4
    Views
    586

    Hi James. I’ve had this in the past and I think...

    Hi James. I’ve had this in the past and I think it’s down to exhaust bore size. This is made worse if the probe isn’t pushed far enough into the system or the car isn’t revved enough during the test....
  8. Replies
    5
    Views
    538

    Thanks for the tip markcro ;-) Yes I tried to...

    Thanks for the tip markcro ;-)

    Yes I tried to remove it with that, but it just flexes and spins around the nut.
  9. Replies
    5
    Views
    538

    That’s cool. Yes, I normally do that but on...

    That’s cool.

    Yes, I normally do that but on this occasion I drove straight to the garage.

    To be fair to the operator he did Rev the crap out of it when testing it.
  10. Replies
    5
    Views
    538

    Emissions Failure

    Hi guys.

    My S14a was off the road for 1.5 years, with only occasional startups, and I want to get back on the road.

    I naively took it for an mot straight out of the garage and it failed on...
  11. Replies
    159
    Views
    20,395

    I'm in

    I'm in
  12. Recommend me a 200 friendly MOT garage in N London

    Hi guys,

    As per title, any recommendations? North London, Enfield area please.

    Thanks.
  13. Replies
    12
    Views
    9,434

    :thumbs: all

    :thumbs: all
  14. Thread: Ds2500's

    by Mario
    Replies
    1
    Views
    836

    Ds2500's

    Hi Dan. Surprised to hear you are shutting dbpower down, but it sounds like its onwards and upwards with the new venture. All the best with that.

    Have you got any ferodo pads for standard front...
  15. Replies
    12
    Views
    9,434

    Cheers Paul. Yes I know it can't be the cat. ...

    Cheers Paul. Yes I know it can't be the cat.

    It has never failed, but as mentioned the exhaust would need to get very hot before the reading got low enough to pass.

    I like the idea of partially...
  16. Replies
    12
    Views
    9,434

    Thanks guys. From your experience pursey, could...

    Thanks guys. From your experience pursey, could it be a very minor blow? As I can't feel anything obvious.
  17. Replies
    12
    Views
    9,434

    High lambda reading on mot emissions test

    Every mot I have the same issue in that it is a struggle to get my car to pass the emissions test, specifically the lambda. The engine has to run very hot before the reading comes within range. I'd...
  18. Jon, I was referring to air in that caliper when...

    Jon, I was referring to air in that caliper when bleeding
  19. Yes

    Yes
  20. Thanks for the replies guys. Maybe pads do...

    Thanks for the replies guys.

    Maybe pads do need to bed in a bit but still should be better than what it is i think.

    Bleed order was rear drive, rear passenger, front driver, front passenger. I...
  21. Brake fluid change & pad renewal, now rubbish braking

    I changed my brake pads and brake fluid, drove, got abs going, re-bled and the bite is rubbish (was fine before).

    Pad wise I went from DS2500 to Pagid, but I don't think the pads are the issue.
    ...
  22. Replies
    61
    Views
    7,609

    Awesome 14!

    Awesome 14!
  23. Replies
    2
    Views
    172

    Thanks mate. Yes straight forward after all. ...

    Thanks mate.

    Yes straight forward after all.

    Now got to find a replacement!
  24. Replies
    2
    Views
    172

    Removing washer bottle pumps

    Is it just a matter of popping them out? Do the black seals that are visible inside the bottle stay in place? I am worried about something coming loose/breaking inside the bottle if I force them off....
  25. Replies
    0
    Views
    1,428

    Brokerage premium up 140%!

    How do you justify a 140% increase in your brokerage premium (up from £25 to £60)?

    I just got my renewal notice, and couldn't get the numbers to add up, and when I called your office they told me...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4