Search:

Type: Posts; User: pointz

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    3
    Views
    153

    Will update once tickets come on sale :thumbs:

    Will update once tickets come on sale :thumbs:
  2. Replies
    0
    Views
    51

    Isle Of Wight Takeover 21/5/2023

    I have booked us a clubstand at the iow Takeover 23.

    Created event on fb bit some may not be on there! Please comment below only if you purchase a ticket!

    Link to event-...
  3. Replies
    3
    Views
    153

    Simply Japanese 23rd July 2023

    First 2023 event date released!


    Last year we had a decent selection on stand let's make 2023 even better!
    Loads of time to organise your calendars :thumbs:

    Please comment below if you have...
  4. Replies
    2
    Views
    92

    Just bolt up some s14 5 stud bearings, they fit...

    Just bolt up some s14 5 stud bearings, they fit direct on s13 knuckles.

    Conceptua performance sell them.

    Z32/r33 rear brakes bolt straight up with s14 bearing assembly and s13 knuckle.

    If...
  5. Replies
    37
    Views
    3,331

    I am using this stuff, I wanted to use the...

    I am using this stuff, I wanted to use the metaflux but wasn't available anywhere at all and still isn't AFAIK

    I have used both previously and have no negative comments on either to be honest!
    ...
  6. Replies
    37
    Views
    3,331

    Picshttps://uploads.tapatalk-cdn.com/20221030/3441...

    Picshttps://uploads.tapatalk-cdn.com/20221030/344108793804fffeeba21d861efc1a6d.jpghttps://uploads.tapatalk-cdn.com/20221030/554d9210bb759a81c48ed60a3b7130ce.jpghttps://uploads.tapatalk-cdn.com/2022103...
  7. Replies
    37
    Views
    3,331

    Engine almost finished. New ACL STD size mains...

    Engine almost finished.

    New ACL STD size mains and big end bearings.

    New genuine oil pump.

    Genuine gasket set.

    Oem rods, +1mm oversize pistons.
  8. Replies
    37
    Views
    3,331

    Plenty more areas of welding...

    Plenty more areas of welding...
  9. Replies
    4
    Views
    439

    Check your base fuel pressure and do a proper...

    Check your base fuel pressure and do a proper boost/vac leak test.
  10. Replies
    4
    Views
    439

    :facepalm: just realised the op was 5 years ago!

    :facepalm: just realised the op was 5 years ago!
  11. Replies
    4
    Views
    439

    As you're fuel pressure is so high it would be...

    As you're fuel pressure is so high it would be the 1st thing I would change.
    It's probably flooding itself on pump prime.

    Do you have an afr gauge? If not I'd recommend getting one.
  12. Replies
    0
    Views
    133

    Ps13 twin projector Bulb recommendations

    Anyone have experience with a decent bright bulb for the twin projectors?

    I need-

    H3C dipped
    H3 High beam

    Currently have HiD dipped but one of them has died.
    Am happy to have hid on...
  13. Replies
    1
    Views
    87

    Quite a few tuners are selling them nowadays, so...

    Quite a few tuners are selling them nowadays, so guess they are reliable and safe to use!
  14. Thread: S13 with 1UZ

    by pointz
    Replies
    2
    Views
    242

    Don't know what help you are hoping for with your...

    Don't know what help you are hoping for with your vague post, maybe ask specifically what in particular you need help with?

    Ecu power is supplied via the connector in engine bay, nearside,...
  15. Replies
    4
    Views
    168

    The torque figure for the main caps is low only...

    The torque figure for the main caps is low only 44-54nm as seen here.

    Here is a link for the workshop manual, you need em section and cylinder block starts at pg 33.
    ...
  16. Replies
    4
    Views
    168

    Does sound like over torquing. All the specs...

    Does sound like over torquing.

    All the specs are in the oem workshop manual tell them to follow these rather than the specs they are probably getting from elsewhere.

    Or very slim possibility...
  17. Replies
    2
    Views
    113

    Not 100% what you are trying to do? Replace the...

    Not 100% what you are trying to do? Replace the oem hardlines on the pump cradle?

    If so the oem ones are brazed or silver soldered in and not easily removable unless you are planning to chop and...
  18. Replies
    3
    Views
    656

    Car clubs are fully subscribed unfortunately, ...

    Car clubs are fully subscribed unfortunately, but if we miss it next year give us a nudge and we will try and sort one.

    Not far for quite a few of us!
  19. Replies
    0
    Views
    398

    Trax @ Silverstone 11th September

    Clubstand is booked, please follow link for booking and once done so please comment below so we can keep the list upto date :thumbs:


    http://www.traxshows.co.uk/

    Club Name:*SXOC*

    Club...
  20. Replies
    189
    Views
    103,160

    I'm not actually sure I'd say at the fly but...

    I'm not actually sure I'd say at the fly but would need to confirm.
  21. Replies
    5
    Views
    233

    Me and 1 other have just booked it, hopefully...

    Me and 1 other have just booked it, hopefully John can join us too.

    Get on it bring the 14 :smash:
  22. Replies
    5
    Views
    233

    That sounds promising :-)

    That sounds promising :-)
  23. Replies
    5
    Views
    233

    Anyone fancy this? Trackday

    https://www.motorsport-events.com/products/9-september-2022-keevil-track-day

    I'm planning to book on in the next day or so if anyone else fancies it?...
  24. Sticky: Pleasure as always, see you in a couple weeks...

    Pleasure as always, see you in a couple weeks :plug:



    No worries always as good as the members that are making the effort!
  25. Sticky: Yes of course, apologies mate my bad.

    Yes of course, apologies mate my bad.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4