Hi! Can you supply a genuine head-exh.mani gasket for RB25, two T3 gaskets, a 3-bolt 3" exhaust downpipe gasket, and a holset HX35 downpipe gasket? Prices please, with shipping to Sweden.
Thanks!
Type: Posts; User: DeJi
Hi! Can you supply a genuine head-exh.mani gasket for RB25, two T3 gaskets, a 3-bolt 3" exhaust downpipe gasket, and a holset HX35 downpipe gasket? Prices please, with shipping to Sweden.
Thanks!
come on guys.. I thought RB25 conversions were common now. Doesn't anybody remember how they wired their speedo?
Almost done with the wiring for my RB25 conversion, thanks to John Bennett's guide and the s13 service manual (LHD so the plugs by the headlight isn't exactly the same). I only have one question that...
you "have to" remove them all. It works if you don't, but it'll be a lot harder to turn the engine over, and you might drain the battery before you're done. You have to take all the plugs out...
remember to floor the gaspedal though to let enough air into the cylinders. As said, just crank it until the needle stops moving. Usually takes 5 seconds or so.
check the cables by the ECU then, if you've just uninstalled an E-manage ultimate. If it looks fine, double check the coilpack wiring anyway with a multimeter from ECU to the ignition chip, and from...
having recently done this I can tell you that the upper rad hose fits perfectly with a bit of trimming (half way on the hose somewhere, there's a bend that fits perfect). The bottom hose fits...
You got both halves of the conrod though right? Cause they're paired
alright.. shouldn't be too hard to find. Thanks
I'm gonna install an RB25 into my s13, and going for a Z32 ECU with Nistune as engine management. However, the type 2 nistune boards require a consult connector to communicate with the laptop, and...
I think I've gotten a hold of a set from somewhere else, but I'll let you know if I still need them
did you loose the std nuts or are they damaged? They're intended to be re-usable
best way is to modify a normal HT lead to fit snugly on the coil, then start the engine and use a normal timing light clipped to the HT lead to check timing
Hi! I've gotten a hold of a set of no-name stiffer ARB's for my S13, and the bushings that came with them are terrible. They're very soft and are supposed to slide on the ends of the ARB, not split....
it didn't do this before you had it mapped right? And you mention it's a "story in its self"? Care to elaborate?
is your engine rattling or are you just going to replace the bearings as a precaution? If it's the latter, then leave it be and start saving up for a real rebuild instead.
If it's rattling and it...
I'll accept the shock-cooling explanation, but that'll only really happen when the water is cold though, right? As when it heats up and expands, it fills up the top tank and expells the air.
awesome :) Thanks :)
Apologies if this has been covered before. I did a search and didn't find anything, so I'm hoping someone else can tell me.
I've got an S14 LSD waiting to be fitted to my s13. Going to have it...
are you sure you aren't looking for a problem where there is none? Is the upper radiator tank supposed to be full? Mine isn't, and it's a koyo aswell. My std radiator did the same thing. As long as...
nevermind actually, already got a hold of these items at a fair price.
New enquiry though : RB25DET GReddy style plenum, how much does it cost to ship two of them to Sweden? Does it accept the...
if the oil pan is off you can jam a piece of wood down the block, between the first crank journal and the block.
you realize there's no way for us to know even slightly how hard you've tightened it by knowing you've tightened as hard as you can, and that you work out? :)
how long was the bar you used to...
Hi :wave:
Do you have a fuel rail for topfed injectors for an RB25? Price?
Also need a fuel pressure reg. What do you have, and how much?
Thanks :)
does it run properly though, or does it feel sluggish on low rpms? Could be the water temp sensor, or the knock sensor.
On the picture of the cam splines, the D-shaped locator looks broken, but I...