Search:

Hi,

I have a problem, after 10-15 minuts of driving my fuelpressure plums down to aprox 1bar. If I park the car for the night, the same thing repeats it self.

Walbro 255 or Bosch 040 (both...

On the way to 1,5bar...

When should the VVT kick in and kick out?

Engine Spec's
http://www.bilgalleri.dk/galleri/117149-nissan_s14_silvia___inte_edition

AFR = 12,0 on full throttle.... is...

My car and I thanks you :)

Turbosmart Eboost2 is gong in the car tomorrow.... 1,5bar come on ;) !!!!!

<center><iframe width="600" height="420" src="http://www.youtube.com/embed/Rk6xtwL2VU0"...

Hi Jez, thanks for the answer.

What does TTL meen?

I just spoke with my tuner www.ttj-engineering.dk, he askes if the coils are getting triggered by a Logic 0-5V signal or they are ground...

Im getting an EFI EURO engine management fitted.... my tuner needs to know whatkinde of ignition coils i have. Is it the inductive or the logic type?

I had the 6 speed box... before i mounted my 350Z box.

You need:
S15 box
S15 driveshafe (the part that goes in to the gearbox because the s15 i bigger)
S15 clutch/ flywheel
...

I have
CP pistons, Manley H rods, BC 264 cams-springs-retrainers
Greddy T67 25G turbokit, KU Engineering w 80mm TB
RPS clutch (max 740nm) and a 350Z 6speed gearbox
EMS: EFI EURO 2 w. MAP sensor...

Thanks :)

I hope my dealer will be able to help me. I don't use FAST because of last time i used it, the dealer got cranky.... lol !
He said that he hated that little punk who uploaded his...

My 6 speed gearbox is leaking/ dripping oil from the rear mainseal where the driveshaft is entering the box.
I can't locate any Nissan dealer in Denmark that is able to help me get a new.

Where...

My S14,5 :)

www.inte.dk

http://www.inte.dk/wp-content/1-custom.JPG

http://www.inte.dk/wp-content/dag-52-013-custom.jpg

You will also need the driveshaft that goes into the box, as the one from s15 is about 3mm bigger.

Your speedo won't work as the s15 box don't have a speed sensor. The speed sensor on the s15 is...

How do I get that to work? Is there a guide somewhere, I can't find any....

I need help :)

JDM spec s14a, I dont know if there is any difference in the wiringharness?

S14 box taken appart.... up next is the S15 box, I hope the plastic gear drive fits the output shaft on the 6speed box.

http://www.inte.dk/wp-content/gearkasse-s14a-011-custom.jpg


Project...

I have red that before, I think I will take one of my S14 gearbox' apart, just to see if it is possible to remove vvs and sensor readout point.

Perhaps i should get the dakota sgi 5 device because...

That could solve my problem :)

http://www.dakotadigital.com/index.cfm/page/ptype=product/product_id=126/mode=prod/prd126.htm

S13 sgi5 fix......

Hi there,

I have bought an S15 6speed gearbox for my jdm S14A.

I was about to connect my 14a wiringharness to the S15 box, when I discovered that the plug for the s14a speedsensor-signal did...

Nice project :)

What wheels are you going to use?
I ask as because I have the same size front breaks :)

I run the Bee R B5 9x17 ET20 wheels.

Get back to work :D!

I pulled the subframe from the car, because I need new bushes.
If i'm going to buy a full set of bushes from your shop, do I need to remove the "iron-bush" that sits in the subframe......?
...

2. Inte - S14A SR20DET StrokerKit


When your getting the pistons spec. made for the kit - will the buyer have the opportunity to choose the compression ratio :) ?

Sounds great :)

I gues the stroke is 91mm?
If you use 87mm pistons your will get ~2,163 L

If you could make a strokerkit for that amount of money - im in :thumbs: !
In the first place I didn't understand why you made a std. size crank when you can buy those at Nissan.
Im going to...

Sorry OT, but what do that thing do?

Im in the need of some:

Full set of Nismo 60mm wheel studs for the REAR.

Black silicone radiator hoses.

Car:
Nissan S14A

PM the prices and shipping cost :)