Search:

Type: Posts; User: speedingmofa

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Not much point in plugging them into a car that...

    Not much point in plugging them into a car that doesn't run, now is there. I have now plugged it into a friends car, and the tachometer was dead. Speedo works. But i hate to have to pull apart a...
  2. Bench testing cluster - speedo and rpm signals

    Hi guys, I want to test an S14 cluster on the bench so I needn't install it in the car and go for a drive to check if the tacho and speedo work. Anyone know what needs done?

    From research...
  3. Replies
    7
    Views
    180

    I know the Z32 lines fit perfectly. Std S14 uses...

    I know the Z32 lines fit perfectly. Std S14 uses banjos at the rear, doubt those fit the Z32/R33 calipers
  4. Replies
    9
    Views
    235

    There is an option in Nistune to disable the...

    There is an option in Nistune to disable the closed loop function, but closed loop is only enabled until around 3500rpm. After that, it's all open loop. It seems there's still something wrong with...
  5. Replies
    0
    Views
    182

    Websites for importing JDM cars

    It's been a while since i've imported a car from japan. Now i'm looking again, and i'm surprised to find the shipping fees have doubled! The car prices have also gone up, which makes it very...
  6. Replies
    10
    Views
    248

    Replace with any from an S14

    Replace with any from an S14
  7. Replies
    16
    Views
    535

    https://www.hfm.parts/shop/brakes/hfm-bm57-brake-m...

    https://www.hfm.parts/shop/brakes/hfm-bm57-brake-master-cylinder-for-nissan-abs-non-abs/
  8. Replies
    5
    Views
    275

    https://www.sxoc.com/vbb/showthread.php?375832-Oil...

    https://www.sxoc.com/vbb/showthread.php?375832-Oil-Restrictor-Needed-for-GT2871r-sr20det

    Minimum of 1mm restrictor
  9. Replies
    5
    Views
    275

    The "R" means it's ball bearing isn't it? If it's...

    The "R" means it's ball bearing isn't it? If it's ball bearing, you need a restrictor... can't remember whether it's 1 or 2mm though.
    About the housings, I'd go for a original, just to ensure all...
  10. Thread: Plenum

    by speedingmofa
    Replies
    11
    Views
    477

    I've heard great things about plazmaman, it's a...

    I've heard great things about plazmaman, it's a piece of art! Don't have any experience myself, but judging from the really short runners, it's great for top end, not so much for low/mid end.

    Best...
  11. Replies
    2
    Views
    145

    The OEM chain squirter usually isn't held by the...

    The OEM chain squirter usually isn't held by the oil pump cover. If it's popped out, pop it back in with sealant or so so it doesn't pop back out with pressure. Leaving it out leaves a big hole in...
  12. Replies
    3
    Views
    236

    Ebay jobby does fine for anything under 350hp...

    Ebay jobby does fine for anything under 350hp really, i had to redo (cut and weld) the elbow under the battery tray. And i did relocate the batt to the rear before that
  13. Replies
    4
    Views
    385

    From what I've seen, it's about 40hp. Same boost...

    From what I've seen, it's about 40hp. Same boost figure at about 400-500rpm later iirc. Probably feels like an eternity if you're used to the smaller housing
  14. Replies
    22
    Views
    1,121

    Sticky: PM me where u got those from plzz :)

    PM me where u got those from plzz :)
  15. Replies
    22
    Views
    1,121

    Sticky: The benefits of this conversation... I guess...

    The benefits of this conversation... I guess sharing a bit of knowledge with the community :D

    This conversion though.... It's only got advantages! A few minor disadvantages as far as i know.
    ...
  16. Replies
    6
    Views
    206

    I seriously doubt the alternator would go that...

    I seriously doubt the alternator would go that soon. Use a multimeter and check voltage levels while idling and raised rpm (3k or so). If it's around 14V, then the alternator should be good, and it's...
  17. Good stuff :)

    Good stuff :)
  18. I dove into the fsm yesterday, an S13 sr20det ecu...

    I dove into the fsm yesterday, an S13 sr20det ecu has different coil trigger signals than S14. You're certain you're not using an S13 ECU or based your wiring on an S13 scheme?

    You're also using...
  19. What motor? EU or JDM? Same for the ECU. Sounds...

    What motor? EU or JDM? Same for the ECU. Sounds like you may have an output switched. Some ECUs have the 1 and 2 on another position if i'm not mistaken.
  20. Replies
    10
    Views
    510

    Did anyone measure the diameter of the tube?...

    Did anyone measure the diameter of the tube? Might look for something more powerful
  21. Replies
    22
    Views
    1,121

    Sticky: The coils i use, use the same pinouts. So the...

    The coils i use, use the same pinouts. So the black ones (1.8T) and red ones (R8) are interchangeable. I've used them and many clients have used them also without any issues.
  22. Replies
    16
    Views
    778

    I've actually fixed a bmw e46 316 like this.. It...

    I've actually fixed a bmw e46 316 like this.. It was overheating, blowing into the coolant. And i poured this stuff into it, kept the heaters blowing and it fixed it. The heaters even continued to...
  23. They don't bottom out, so any would do as long as...

    They don't bottom out, so any would do as long as it's not a foot long... I'd say 10-15mm
  24. Def M5's, checked yesterday for ya. Might be a...

    Def M5's, checked yesterday for ya. Might be a good idea to switch to Allen head bolts. Give them a good wack with a hammer before trying to remove the old ones
  25. Replies
    1
    Views
    159

    After getting so many replies (enter sarcasm) i...

    After getting so many replies (enter sarcasm) i decided to get close and personal with the FSM's and google and check things out for myself.. Theoretically, i got all the info i need to do this...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4