I knew I'd have a few issues I will find while finally using the car but the csv going twice now is rediculous haha. Just need to find another starter motor and hopefully nothing else goes wrongs.
...
Type: Posts; User: mospin
I knew I'd have a few issues I will find while finally using the car but the csv going twice now is rediculous haha. Just need to find another starter motor and hopefully nothing else goes wrongs.
...
Update now fixed it was a faulty cold start valve and warped thermostat seem to be running fine now apart from the starter motor has died on me.
Sent from my CLT-L09 using Tapatalk
Update with the above advice I've check all the following.
And I've found the cold start valve was seized fully shut on cold. strange that so again I've replaced it for another
I also found the...
Breathers from rockers to catch can
Pcv blocked off.
Sent from my CLT-L09 using Tapatalk
No I had a idle issue before over a week ago so changed the sensor and that fixed the issue so the sensor is a week old.
Ive just tried another sensor with same results
Sent from my CLT-L09...
Sorry forgot to say this was replace last week for a new one
Sent from my CLT-L09 using Tapatalk
Okay back on getting issues on the ca18det again.
From cold car starts fine and runs great even when warm no issues driving it no hesitation nothing. But as soon as its up to temp the car idle...
I had my cas fully advance after doing the timing belt and I counted the teeth and checked it so many times.
Eventually gave up taking the timing off the loop and used a ht lead on no. 1 coil and...
New update.
Changed the adjustable cam pulleys for stock ones and the car now idles at 800rpm but was still trying to stall on cold start.
So had a feel around for leaks on the iacv and found...
Update,,, I've now change fuel pump, filters, rail and injectors and fuel pressure is much better but still drops a little when revved but if I hold the throttle until its warm it will stay idle...
Little update.
Plumbing a fuel pressure gauge into the line gave these results.
Pump primed just shy off 40psi
Engine running at 400rpm only 2.5bar
When revving increased it drops just...
Yes my breathers go as follows
Breather on Rocker inlet side to catch can
Catch can to inlet pipe on turbo
Pcv on inlet blocked
Exhaust cam Rocker blocked
This was how it has run before...
Il give him a try.
Done a boost leak test and nothing shows up so it must be fuel related
I have spark and fuel so I'm guessing ignition system?
Sent from my CLT-L09 using Tapatalk
Changed temp sensor today back to the oem one and shows as working.
Still won't start but if a apply the slightest throttle it start straight up and as soon as you remove the throttle it stalls...
Sounds very similar to mine I will however give it a try and see what happens it would be nice for it to be something so simple.
I've tried everything else I'm going to redo a leak test as well...
I replaced the temp sensor with another I brought from a local car factor's code 22630-51E02
I've done all checks with multi meter and it shows as working.
The only way to run the car is with...
Stage 2 ca18det having trouble trying to get it running again.
Symptoms. Won't start cold or hot unless keeping the throttle held only.
It did have code 13 and tps code, also pin 30 track burnt...
Just ran the stock s13 lights wire to both kouki lights wires so 1 into 2
Same for brakes 1 into 2
And double down with thicker earth wire this is what I've done with no problems .
As for...
ep racing website has four different types off these lights, 1 set looks close to the above picture.
This is now fixed turned out when fitting the front facing inlet I plumbed the idle control valve wrong and back into the inlet the car now starts from cold :)
Sent from my SM-T335 using Tapatalk
No splines are fine I've manage to get it sitting on 15tdc now it was a case off adjust the tps and idle screw to move the markings so I could adjust the cas . I'm still not happy where the cas is...
Just noticed I've made a typo instead off timing setting 10 it's ment to be 20
As the timing goes from left to right up in 5s so 0,5,10,15,20,25,30
I can get the cas to 20 but then the cas is...
In my ownership no , engine is from a r32 gtst auto I heard the engine running and everything checked out including compression,
Since then I've rechecked compression and it's near 174 across...
Okay this is been driving me crazy for a few months now and I'm completely stumped , I'm doing a rb20det conversion and I just can't get the timing correct
Closest I can get it too is 10 but the...
Tdc garage services Ltd,
Is the new name if you need to look him up
Sent from my SM-T335 using Tapatalk