Thanks Mate - now I need to find some suitable width carbon/kevlar :D
Dwayne
Type: Posts; User: DarkLight
Thanks Mate - now I need to find some suitable width carbon/kevlar :D
Dwayne
Hi Folks, could anyone tell me the maximum dimensions of an S15 Bonnet please?
Thanks
Dwayne
Paypal cash sent :thumbs:
Dwayne
Going to be anodising mine :thumbs:
Dwayne
Dropper resistor should be found on the near side inner wing ( or it's general location) It is a rectangular silver alloy lump with a ceramic core and 5 leads (all black) from one end. Originally...
Worth checking the connections to the box, also TPS as this causes all sorts of wierdness. You can also do a self diagnosis of the box to check that the computer is happy, the proceedure is in the...
Make sure the injector is firing.
The plug should be wet when you take it out, but it's better if you can listen to it. If it's running it should tick
If it isn't then the first place I would...
I've done this a couple of times (trashed first set of disks on the track :wack: )
remove original disk, if you position it carefully face to face, the 8mm holes for removing the disk line up...
If it runs, tow it with the engin running in neutral, if it doesn't then disconnect the propshaft - or start looking for a manual box for the conversion
Dwayne
I run a SSQ on my auto. helps to stop me blowing induction hoses off when the T28 is running at 15psi. Otherwise I don't think it makes much difference really
Dwayne
Ouch :wack:
I wouldn't have expected to pay more than about £30 +vat ( don't think I would have the front to charge more)
Worst case senario - Purchase cheap bench type pillar drill (£35 or...
Bloody Hell !! :eek: :eek: :eek: :eek:
I did my new fronts with a power drill & a couple of M8 bolts on the drive - took about 10 mins each in total. A pillar drill makes life easier, but £80...
I'm currently using Black Diamond Preditor pads - S14 pattern are around £49 per set (demon tweeks) but seem pretty good so far.
Not tried the EBC pads but Black Diamond are highly rated on a number...
Replace the Pipe & all unions.
Local motor factors or accessories shop should be abl to sort you out.
Roll of cupronickel brake tube ( doesn't corrode like steel) about £15, Flaring tool - about...
I've had my S13 for a couple of years & have never had a problem with my little girl in the back. Child seat was a bit of a pain to fit but otherwise OK. Sure a 4 door may be a little easier to get...
I've got one of those,
6x line outputs for front, rear & indipendant sub. Excellent sound quality from CDs (leave the Anti distiorion filter off as it sounds better) Unfortunately, I run it fully...
Unfortunately I did this with my speedo some months ago - basically it's fooked.
I can actually brake from 60 to zero, apply the handbrake & according to my clock I'll still be doing about 30, &...
Sounds like you have a couple of the coil pack trigger leads back to front & she's trying to fire the wrong piston in the wrong place. Check the wiring etc.
Dwayne
Personally I'd agree with Nismo_joe - The FNIC isn't going to make a huge difference at stock boost etc, perhaps 2-3hp at full tilt, the open air filter is probably worth around 5hp max. Add a couple...
Hi & welcome :wave:
If you have the zorst & intake all you need is a decent fuel pump & one of Mr Horshams finest chunks of silicone to make a basic stage one :D :D
Do be careful with...
Getting better :cool: :cool:
Hope she likes it
Dwayne
Doesn't sound normal to me. I generally find front pads wear 4-5 times faster than rears (expected as front do most of the work) but should wear roughly evenly (to within a mm or so)
Dwayne
Happy birthday :thumbs:
Dwayne
Congratz mate, They are worth every sleepless night, smelly nappy etc ...:thumbs:
Agreed
Dwayne