Search:

Type: Posts; User: bahis

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    11
    Views
    204

    I got a Driftworks BGW. ...

    I got a Driftworks BGW.

    http://www.at-r.fi/content/images/media/project_200sx_s14/s14_p09_013.jpg

    http://www.at-r.fi/content/images/media/project_200sx_s14/s14_p09_009.jpg
    ...
  2. Replies
    4
    Views
    207

    My block doesn't touch the flange.:(

    My block doesn't touch the flange.:(
  3. Just like Chriscooke said. FPR goes to the engine...

    Just like Chriscooke said. FPR goes to the engine side of the plenum. Are you replacing the stock FPR with something else?
  4. Number 2 goes to the thermostat housing. Here is...

    Number 2 goes to the thermostat housing. Here is a pic:
    http://at-r.fi/content/images/media/random/line2.jpg

    Number 1 goes to the intake manifold. Don't think I have a pic of that atm.
  5. Thread: Big end bearings

    by bahis
    Replies
    5
    Views
    211

    I have used ACL before and just put a new set for...

    I have used ACL before and just put a new set for big ends and mains...
  6. 1/2 are water lines. 6 goes to fpr.

    1/2 are water lines. 6 goes to fpr.
  7. Replies
    13
    Views
    289

    You do know that the engine is all aluminium so...

    You do know that the engine is all aluminium so there shouldn't be any rust in the cooling system... Well the rotor of the water pump is steel so if you are running only water it might rust...
  8. Luckily no. . It has been in there for the last 5...

    Luckily no. . It has been in there for the last 5 years.... :D
  9. Replies
    0
    Views
    89

    Oil pump o-ring size.

    I need the o-ring that goes between the oil pump and the block. Does anyone know what size it is?
    I could get one from Nissan, but it would take two weeks...
  10. Sorry to bump an ancient thread, but I found the...

    Sorry to bump an ancient thread, but I found the shim!

    It was....
  11. I have almost identical setup. (Except I have...

    I have almost identical setup. (Except I have GTX2867R Gen2 with 0.64 A/R housing and Nistune) I'm building the engine now so don't know yet how much power it will make. Will let you know when I get...
  12. Replies
    1
    Views
    170

    crank main bearing caps

    I started to put my engine back together, but can't rememer which way the main bearing caps should go.
    Does the notch in the bearing go to the same side as the notch in the bearing in block or to...
  13. Replies
    24
    Views
    738

    Or valves can be machined to same height, then...

    Or valves can be machined to same height, then you can use the original shims that are all the same thickness. (At least mine were)
  14. Replies
    6
    Views
    273

    With some csms you can keep the vvt, but when...

    With some csms you can keep the vvt, but when using stiff valve springs the vvt sprocket will start to rattle very quickly...
  15. Replies
    37
    Views
    791

    But if you get stiff springs your vvt will most...

    But if you get stiff springs your vvt will most likely start to rattle very quickly.
  16. Replies
    37
    Views
    791

    My gearbox lasted a few years with ~430hp before...

    My gearbox lasted a few years with ~430hp before the third gear exploded...
  17. Replies
    5
    Views
    275

    At least with gt3071r using a restrictor was not...

    At least with gt3071r using a restrictor was not recommended as it has one built in. I asked it from local garrett importer... But it's very important to have oil return without any bends. That said...
  18. It was a set with both SAE an metric sizes marked...

    It was a set with both SAE an metric sizes marked in the sockets, might actually be something from between... I need a new set :wack:
  19. Turns out it was 10mm 12-pt after all. My 10mm...

    Turns out it was 10mm 12-pt after all. My 10mm socket was actually 3/8 (9.55mm)
  20. Replies
    10
    Views
    335

    Are you sure that the valves are exactly the same...

    Are you sure that the valves are exactly the same height?
  21. What socket do I need to remove the piston oil squirters?

    I was trying to take the oil squirters out of the block as I'm taking it to a machine shop for honing, but didn't have the right socket to get the bolts out.
    It's something from between 10mm and...
  22. Replies
    10
    Views
    254

    I have standard studs with Rota GTR-D 12" ET20...

    I have standard studs with Rota GTR-D 12" ET20 and 5mm spacers. At least with these wheels the lenght is good.
  23. You need to do a pressure test to find possible...

    You need to do a pressure test to find possible boost leaks.
  24. Replies
    5
    Views
    252

    Boost leak?

    Boost leak?
  25. Thread: Camshaft vs VTC

    by bahis
    Replies
    9
    Views
    395

    I lost about 50nm of peak torque and my gt3071r...

    I lost about 50nm of peak torque and my gt3071r spools about 300rpm later without it. But some of that could be recovered by adjusting the cams. (I replaced the vct sprocket with adjustable cam gears)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4