So used to have hsd monopros, sold them and bought brand new HSD dual tech's and I hate them so jumpy even with no preload and the dampers set to the softest settings, it's a road car and I'll be...
Type: Posts; User: ali-d1936
So used to have hsd monopros, sold them and bought brand new HSD dual tech's and I hate them so jumpy even with no preload and the dampers set to the softest settings, it's a road car and I'll be...
Recently fitted a Viper alarm, very happy with the outcome, has lots of features, one being after the car is started the doors auto lock, I can see me locking myself out of the car yet and I'd like...
Hi bout a gizzmo ms-ibc v1 years ago just got around to fitting it today, I know gizzmo has manuals on there web site but the link to the version 1 is broken.
Has anyone a copy of one handy just to...
Had the exact same noise last month, noise was there when the clutch was pressed in all the way or just as the clutch bit but was fine once clutch pedal was fully released /engaged, wound up changing...
Hi guys,
Bought a set of Hsd dualtech coilovers brand new from driftworks, before this I had a set of hsd Monopros and loved them, but they had a knocking rear mount and I sold them on for these. ...
Anyone any ideas? I'm really stumped
Just did it today, pulled off the drivers side wind and got a vice grips around the bottom of it where it wouldn't be seen, once I could get my hand on it I slowly pulled it off and it came out and...
4years ago the clutch destroyed itself,
So I bought a exedy clutch, pressure plate, driftworks lightened flywheel for 6speed box, release bearing and spigot bush, car drove for 50miles and I...
Anyone?
Where would be the best place to get a good set of Ngk plugs?
Had a light miss fire on Idle, assumed my coilpacks where on the way out, but testing the coilpacks after a run they all returned a 1.65~1.69 reading so I'm guessing they are good
Spark plugs ...
O2 sensor?
Windscreen mold removal,
Have a bubble of rust forming above the windscreen, want to get in and look at it and see if I need to remove the windscreen to get it repaired properly,
Checking the...
Had nightmare trying to figure out my airbag light, same as you fuse was removed, replaced fuse took 5maybe 6attempts to get the airbag light to reset so maybe keep trying,
If you look into it...
I got two nuts and welded caps on top of them for the feed and return line through the firewall, not sure if needed, cannot remember the size or pitch off the top of my head
What gague Wire would you recommend?
Hi guys,
Just looking for some advice on s15 coil packs
Mine are on the way out again, so would like to upgrade to a more modern coilpack design, herd ALOT of people switching to vag coil packs...
Hi all,
Have a feeling my historical oem coilpacks are causing a rough idle,
I'm running a standard S15 spec-R, just looking for some new coilpacks to test it out, I'm a wear of the vag...
Checking the diagrams the only earth's that system uses are the two earth's on top of the manifold iv cleaned then and tightened them again unless I'm missing something?
Put in the fuel tank and...
well went all over the car today with a Multimeter
Terminal 38+47 Power supply ECU is getting 12V
Terminal 36 Ignition Switch is getting 12V
Terminal 34 Starter signal is only...
thank you will check that, went throught the Nissan Service manual for the last hour, got loads about the startup proceadure on the EC section of it, so i will know what pins to check on the ECU...
Right so car has not started in about 2 years :rolleyes: its a 99 spec-R
I pulled out a sparkplug and eartherd it off the side of the Engine and no spark,
used a Multimeter to measure the values...
Well this project took a scary turn for the worst,
After i finished the front i attacked the back of the car.
After first inspection it looked grim tbh,...
Thanks for the info Shikari!!
I did see some threads but they where all years old and i thought maybe new products might have come out est then.
But is there any por15 or hydrate 80 style...
Iv pulled the carpet and the sill covers and there is no sign or rust from the inside at all :confused:
and i checked through the hole in the bottom of the sill and the inside sill further up is in...