Just a word of warning dude, if you run your catch can to atmosphere ( normal Inlet side pipe)
Make sure you remove the pcv and block the hole up.if you don’t the pcv will draw air in on...
Type: Posts; User: morzy2k5
Just a word of warning dude, if you run your catch can to atmosphere ( normal Inlet side pipe)
Make sure you remove the pcv and block the hole up.if you don’t the pcv will draw air in on...
I always use the copper NGK BKR7E.. same as the iridium ones but if the temp gets to hot in the cylinder the copper just melts instead of dropping off and peppering the piston crown and cylinder head...
This is very interesting.does it not cause problems higher up the Rev range? As far as I’m aware the vct works from 1100 to 5700rpm
I changed my valve springs in situ with the head still on, piece of cake buddy just took my time. It was one of the best modifications I have done as the standard valve springs are very soft. It revs...
I'm running the Brian crower springs in my car dude, they are a lot stiffer than the standards.i changed mine as I was getting valve bounce high up in the rev range.
The one circled blue goes to the back left side of the rocker I think.its what the pcv valve pipe goes on to
Surely if he hasn't ran it since he heard the faint knock,he will be able to throw a set of matched shells in and it will be good.aslong as the crank has
Not picked up at all/doesn't have any...
I have used one of these buddy but the stage 2a one. They are identical to the H-Dev chips/boards.....when I plug my car into consult it even comes up h-dev!!!! Mine is perfect mate can't fault it.
Done
Ahhh bugger!! Do you know any where else I could get one from,I wouldn't mind buying new genuine if the price was right.
I'm after the jdm 14a bumper, I remember seeing a company making copies of them out of fibreglass but I can't seem to find them/remember the website. Could any one point me in the right direction. If...
Haha no perfect roads here,it's my weekend toy and don't daily driver her anymore so Its meant that I can turn it more track/drift focused.
What springs rates have you got on your bc'a buddy? As that plays a massive part,could you not get some softer springs
I've currently got the hsd mono pros on mine and I love them.the only thing I'm Doing is changing the spring rates as 7kg front and 5kg rear is too soft for me. I'm going to 12kg front 10kg rear. But...
It's the coil pack loom earth. And the correct bolt method is down the back of the cylinder head with a 12mm bolt.nots a pain in the arse to get to in its normal position lol. If it was mine I Would...
I originally bought a exedy organic clutch and it was genuine..lasted 3weeks before it started slipping it was garbage!! If you are planing on abusing the car i.e. Hard driving,launches,clutch kicks...
Competition clutch stage4! I can't rate mine enough,it's a paddle clutch and is rated 450/500fltbs of torque. I can clutch kick mine and do 5k launches all day long and it never ever slips.
I made one my self.cost me about £20 iirc
Just wanted to say I have figured it all out with the help from that link. For future reference my car has a 3.9 auto diff and 17x9.5 wheels with 215 40 17 fitted.
My speedo was originally set to...
Listening to that video it doesn't sound quite that bad.you may get away with a new set of shells and just a crank polish buddy.
I have seen that this afternoon,but was unsure as it says it's for z32/300zx gearbox you see. I have already worked out the percentage i need to bring the speedo down by to get the right speed. My...
I've got a s14 auto diff fitted (3.9) and my speedo over reads so if I'm doing 80 on the speedo I'm actually only doing 68/70mph in real terms (gps) has any one managed to sort there's out?its bugged...
What about a 4door skyline or Nissan laurel?
What plugs were you running?coppers or iridiums? This is always my fear that the plug tip will melt and bounce around the cylinder. Feel your pain you've not had much look with the car this year.it...
I use copper bkr7e in my 2a 14a. They are about £12 for a set of 4!!