The diameter of the wheel shouldn't affect rubbing as the rolling radius of the wheel plus tyre should be the same (within a few mm) no matter what diameter wheel you run. If the wheel diameter...
Type: Posts; User: Fil
The diameter of the wheel shouldn't affect rubbing as the rolling radius of the wheel plus tyre should be the same (within a few mm) no matter what diameter wheel you run. If the wheel diameter...
Try posting in the "Wanted" section bud ;-)
Vacuum lines on the steering pump? May be look at using the pump off an R33 GTSt. They don't have any vacuum lines. Not sure if the mounting brackets are the same though...
Link to the 121 Epoxy Mastic for you:
http:// www.rust.co.uk/epoxy-mastic-rust-proofing-paint/c28117/
It's top stuff ;-)
I know a bit about RB conversions Mike ;)
I stuck an RB25 in my S13 a few years back, using a Syko mount kit, but I've never been too happy with the front anti roll bar fitting. It's an uprated (ie thicker) ARB, and rubs the front of the...
Stick me in the hat too please ;)
You got it Mike. This is going to be a proper job bud ;)
Yoohoo Mike, I'm watching now butt :-x
I bought some high temp vinyl Brembo decals for my F40 calipers off ebay and they've been fine. They've been on for about 3 years with no issues. I painted the calipers in high temp black paint,...
My tacho works without the resistor, it just over-reads. I've never quite got round to fitting a resistor, but hopefully when I do it will bring it back into line.
You might also want to check the oil level once the light goes out as you will be filling up your remote oil cooler snd filter, which will take a fair bit out of the sump ;)
It will take a surprising amount of cranking to get the light to go out! If you keep cranking it for a while longer, but only in short bursts (so you don't burn out the starter circuit), the lught...
Cheers arry, a 'factory' look and feel is what I'm aiming for.
Let us know what transpires ;)
Haha, that's what I've got on there currently! The only issue is that the buckle receptacle sits right on your hip bone/pelvis. I imagine that might be a bit dodgy in a crash.
Erm, am I overthinking...
Hi Steve
You can, but the metal strap the latch is attached to is quite a bit longer on the S13 so it sticks up a fair way and I'm not sure how tight it would hold you if the worst should happen......
I'm putting some R32 GTR front seats in my S13, but the seatbelts are causing me a bit of vexation at the moment...
The belts and buckets are not compatible between the two cars and I've taken the...
Hi Andy, will 6kg be a bit too light for street use? I've got a single plate ORC jobbie in at the moment and its a pain in the arse because it doesn't carry enough inertia.
Just so i know, how...
Hi Andy,
I have an RB25DET in my car and I need a new clutch and lightweight flywheel (but not too light!) to replace the existing set up I have. As the car is only used on the road I'm thinking...
Good stuff mate, glad you've stuck with S bodies ;)
Mines been off the road for 12 months while I've been building an MX5 trackday car, but she'll be back on the road again soon hopefully. She's...
Yes mate, I do remember! Have you still got yours? S14 I think wasn't it?
If it's made from urethane then it's an extremely rare OEM 'Aero' bumper (not Nismo, just a Nissan factory option). You will be very lucky to come across an original factory one, so a decent copy is...
Don't see many S bodies round my neck of the woods! Heading towards Hopton Heath from the Bucknell/Bedstone direction. Looked like it had bronze coloured wheels, but didn't really take in too much as...
Welcome back buddy! Good to see you've still got the old girl. I've got one of your RB25 swap looms in my Sil80 which is still going strong on the rare occasions it gets to come out and play :)
Oooh, very nice. Dare I ask how much the gearbox cost??