Search:

Type: Posts; User: ps13ben

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    13
    Views
    516

    Hi ya matey :wave:, yea you'll find more sense on...

    Hi ya matey :wave:, yea you'll find more sense on here than that shit house facebook
  2. Replies
    6
    Views
    468

    yea thats exactly what i did in the end and part...

    yea thats exactly what i did in the end and part from one of the seals leaking slightly it works perfect, i didn't change the booster though. have you?
  3. Replies
    1,324
    Views
    33,906

    haha even moaning about the phrase 'remoaner' :)

    haha even moaning about the phrase 'remoaner' :)
  4. Replies
    6
    Views
    217

    In the end I managed to find a company to rebuild...

    In the end I managed to find a company to rebuild the rack and itís a lot better and more responsive for sure.
    Also popped some solid rack mounts on there as mine were good to no man and itís...
  5. Replies
    7
    Views
    235

    Yea brilliant thanks for that, Iím sure that...

    Yea brilliant thanks for that, Iím sure that answers the questions of quite a few gents on here.

    I shall get one ordered up and Iíll change it out the same time I change the gearbox gasket and...
  6. Replies
    7
    Views
    235

    Ahhh thanks man, I was kind of swaying towards a...

    Ahhh thanks man, I was kind of swaying towards a new unit to only go through the trouble of changing it just once.


    Sent from my iPhone using Tapatalk
  7. Replies
    7
    Views
    235

    ahh thanks for that, I was hoping it wasnít going...

    ahh thanks for that, I was hoping it wasnít going to be a bugger of a job.
    I just need to find the part number and somewhere that sells it now.


    Sent from my iPhone using Tapatalk
  8. Replies
    7
    Views
    235

    PS13 Prop centre bearing replacement

    Just on the off chance has anyone replaced their prop centre bearing lately?
    Mine is in need of replacement and was wondering where to either take it to have it replaced or to buy and replace it...
  9. Replies
    10
    Views
    233

    Ahh lovely thanks for that jay, Iíll grab a few...

    Ahh lovely thanks for that jay, Iíll grab a few bottles tomorrow and change it out over the weekend [emoji4]


    Sent from my iPhone using Tapatalk
  10. Replies
    10
    Views
    233

    is that what you use Jay?...

    is that what you use Jay? https://www.eurocarparts.com/p/wynns-automatic-transmission-treatment-325-ml-555770520
  11. Replies
    10
    Views
    233

    Right so ill aim for the Dexron 3 then, I can't...

    Right so ill aim for the Dexron 3 then, I can't see the fully synthetic version at Halfords so ill have a look around at partco and the other car parts store. I've just had the rack rebuilt so I'm...
  12. Replies
    10
    Views
    233

    Ahh crap, thank god I didn't put the bugger in...

    Ahh crap, thank god I didn't put the bugger in there then. I don't even know why I thought it was, must have been in a rush to buy it...
    might just get some of the Halfords stuff, at least I can...
  13. Replies
    10
    Views
    233

    Power steering Fluid

    Ive gone a brought a bottle of Fuch ATF fluid for the power steering on the PS but I'm feeling I may have dropped a bollock with it not being Dextron? would the attached be ok?...
  14. Replies
    3
    Views
    213

    Thanks for the reply gents, I didnt realise...

    Thanks for the reply gents, I didnt realise anyone had replied as I didn't get a notification, anyway
    In the end I went for a set of 22mm extended tie rods (S14 tie rod length 22mm extended) and a...
  15. Replies
    7
    Views
    244

    if it goes wrong at least you havent spent a ton...

    if it goes wrong at least you havent spent a ton of money on it, probably won't be as efficient as a well known brand but hey if it makes the right noises then jobs a gooden....

    some of those...
  16. Thread: LED H1 Bulbs

    by ps13ben
    Replies
    9
    Views
    284

    Never used the LED lamps before, how are they in...

    Never used the LED lamps before, how are they in terms of light and how long they last?
  17. Replies
    3
    Views
    213

    S13/ S14 tie rod lengths

    Could anyone shine bit of light on the differences in length between the S13 and S14 tie rods lengths please
    I have changed over to the Geomaster V2 front knuckles with S14 lower control arms on the...
  18. Replies
    6
    Views
    217

    like if you was to loosen or tighten the track...

    like if you was to loosen or tighten the track rod arm to the rack and the rack spline rotates in either direction if that makes sense? blooming hard to explain
  19. Replies
    2,132
    Views
    227,932

    Id hate to think of the monstrosities that has...

    Id hate to think of the monstrosities that has happened to that to make it what it is.
  20. Replies
    6
    Views
    217

    was also looking into this as mine is now leaking...

    was also looking into this as mine is now leaking from either end, Jon does your rack spline have any radial movement at all. say about 3mm rotation in either direction?
  21. Replies
    20
    Views
    571

    I must admit i went for a set of front Geomaster...

    I must admit i went for a set of front Geomaster 3 knuckles in the end as it seemed like a good all round solution with the added bonus of quicker steering, only problem is i brought them second hand...
  22. Replies
    35
    Views
    1,708

    really digging the look of that, looks awesome!

    really digging the look of that, looks awesome!
  23. Replies
    20
    Views
    571

    Well in the end I went for a new set of front...

    Well in the end I went for a new set of front knuckles and rack offset bushes which correct not only bump steer but roll centre too and hardrace rear roll centre correction ball joints (thank you...
  24. Replies
    20
    Views
    571

    Yeah I completely agree being an overlooked...

    Yeah I completely agree being an overlooked upgrade for sure,
    its not as stable as id hoped so just tracking down the issues to bring it back up to what it should be. bloody interesting to say the...
  25. Replies
    20
    Views
    571

    I don't think 10mm will be enough of a...

    I don't think 10mm will be enough of a correction, I take it the ball joint option wouldn't be able to correct huge amounts.
    maybe looking into the knuckle option would be what I need because you...
Results 1 to 25 of 194
Page 1 of 8 1 2 3 4