Search:

Type: Posts; User: immy21

Page 1 of 20 1 2 3 4

Search: Search took 1.95 seconds.

  1. Replies
    9
    Views
    133

    Yes but it's easy to check. On a cold engine...

    Yes but it's easy to check.
    On a cold engine open up Nistune then see if coolant temp is reading the same as outside temp.
    Then run the engine until hot watch coolant temp.
    Check what temp the...
  2. Replies
    9
    Views
    133

    Single is temp sensor for dash Double is temp...

    Single is temp sensor for dash

    Double is temp sensor for ECU, 1 wire is 5v pull up from ECU, sensor is resistor then ECU measures the resistance (EDIT: by looking at the returned voltage)...
  3. Thread: HID advice

    by immy21
    Replies
    21
    Views
    518

    What LED kit did you go for? I'm looking to...

    What LED kit did you go for?
    I'm looking to upgrade the high beams, LED's for them make more sense due to the on\off nature.
  4. Thread: Sub connection

    by immy21
    Replies
    5
    Views
    177

    Got a link of what you bought?

    Got a link of what you bought?
  5. Replies
    10
    Views
    325

    What were you doing when on the limiter? For...

    What were you doing when on the limiter?
    For example late gear change? clutch kick? holding a drift? free rev'ing while not moving? full throttle?
    Help us understand the situation better.

    Of...
  6. Replies
    10
    Views
    325

    What ECU? Ignition cut or fuel cut rev limiter?

    What ECU?
    Ignition cut or fuel cut rev limiter?
  7. Replies
    8
    Views
    234

    Then look at their updated rb25 box conversion

    Then look at their updated rb25 box conversion
  8. Replies
    8
    Views
    234

    This is the most detailed pro's/con's write up...

    This is the most detailed pro's/con's write up I've came across

    http://alphaomegaracing.com/i/7/Choosing-a-gearbox-conversion-for-your-180SX-S13-S14-or-S15.html
  9. Replies
    14
    Views
    514

    Here's another angle on it. ...

    Here's another angle on it.

    https://youtu.be/_sEDuNGnRKA
  10. Thread: Snowboarding

    by immy21
    Replies
    24
    Views
    952

    Pic from last year really does, that's clouds!...

    Pic from last year really does, that's clouds!
    Problem is, heaven ain't cheap :wack:

    I posted on the wrong thread, supposed to be this one:...
  11. Thread: Snowboarding

    by immy21
    Replies
    24
    Views
    952

    Les Houches 2019...

    Les Houches 2019...
  12. Thread: Camshaft vs VTC

    by immy21
    Replies
    9
    Views
    385

    I had 80ft ibs difference with VVT working and...

    I had 80ft ibs difference with VVT working and not working.
    GT2871r and Poncams (256) stock VVT sprockets.
  13. Thread: Back again

    by immy21
    Replies
    3
    Views
    686

    :wave: Look forward to seeing it hit the road!

    :wave:
    Look forward to seeing it hit the road!
  14. Replies
    4
    Views
    231

    Partially drill 3 holes into the boss for the OE...

    Partially drill 3 holes into the boss for the OE blue plastic self canceling piece to mate with, job done.
  15. Replies
    16
    Views
    622

    Same part number as the one's I used:

    Same part number as the one's I used:
  16. Replies
    16
    Views
    622

    I used Ford bolts on my old S14a as per Mark's...

    I used Ford bolts on my old S14a as per Mark's post in the following thread
    If they are the correct thread, pitch and length, use Jag tightening specs in case it's a stretch bolt like the Ford...
  17. Replies
    11
    Views
    422

    I snapped the counter shaft with a clutch kick,...

    I snapped the counter shaft with a clutch kick, my guess is you have done the same.
    Get the box off, should be obvious what broke.
  18. I had something very similer, as mentioned...

    I had something very similer, as mentioned probably the clutch slave.
    Remove the clutch slave, pump clutch pedal and the piston will pop out the slave, clean the sludge out from the rubber piston...
  19. Thread: R35 MAFs

    by immy21
    Replies
    9
    Views
    346

    Not that one, but found this:...

    Not that one, but found this:...
  20. Thread: R35 MAFs

    by immy21
    Replies
    9
    Views
    346

    Lot's of people have used Z33 MAF's, including...

    Lot's of people have used Z33 MAF's, including myself.
    No point buying a Z32 MAF anymore unless it's required predefined map, HD etc

    They seemed to be sold for around £60 with OE 350z housing...
  21. Replies
    6
    Views
    227

    Japex are legit, I got my Nismo 740's from them.

    Japex are legit, I got my Nismo 740's from them.
  22. Replies
    18
    Views
    430

    Front of the car I put the washers between the...

    Front of the car
    I put the washers between the bolt and spring.
  23. Replies
    18
    Views
    430

    They are copper washers out of my assorted metric...

    They are copper washers out of my assorted metric copper washer set, can't remember what size I used.
  24. Replies
    18
    Views
    430

    I leave the spring in, add washers between the...

    I leave the spring in, add washers between the bolt and spring until the bolt won't fully seat, then remove one shim and your good. iirc 4 shims meant the bolt wouldn't fully seat so for me 3 shims...
  25. Replies
    18
    Views
    430

    Try locking out the stock bias first, all it will...

    Try locking out the stock bias first, all it will cost you is time and some cheap brake fluid, put good stuff in once your happy with the setup.
    What rear calipers have you got?
    What front and rear...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4