Search:

Type: Posts; User: d-lo_200sx

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    243

    I thought same sorta thing mate, I'll get it...

    I thought same sorta thing mate, I'll get it jacked up and take a look tomorrow I'm not quite sure what's been rubbing though I did away with the arch liners and moved the loom higher so I haven't a...
  2. Replies
    2
    Views
    243

    S14a stage 3a Won't start PLEASE HELP

    Hi all,

    I'm hoping you lot can help me out here guys, To put this in short I have recently got the car back on the road after having it off the road whilst spraying some engine bits and few other...
  3. Replies
    12
    Views
    560

    Checked mine (apex) it does have a pipe...

    Checked mine (apex) it does have a pipe underneath but it is further down pointing up towards the throttle
  4. Replies
    12
    Views
    560

    I've got same intercooler for my s14a but mines a...

    I've got same intercooler for my s14a but mines a apex one and that doesn't have that small tube underneath only had a DV pipe on mine, but even so the fan shroud does need a bit of a trim away where...
  5. Replies
    0
    Views
    287

    Stage 3a....

    Hi mate

    I've got a stage 3a board in at the minute is the board re-writable so I could have it custom mapped? If so how much is it for the custom map / unlocking?
  6. Replies
    23
    Views
    1,114

    Hi mate don't know if you got ya answers already...

    Hi mate don't know if you got ya answers already or not pal, but I've got a very similar setup and had some similar problems the stalling turned out too be the z32 over reading the air coming back...
  7. Replies
    16
    Views
    1,550

    You could go for the GTX3076r the newer version...

    You could go for the GTX3076r the newer version of what fikemoo has, not 100% sure on the differences between GT & GTX turbos but I know he compressor wheels are different GT has 6pairs of blades (1...
  8. Replies
    20
    Views
    1,147

    Yea that would be fine just scotch it back make...

    Yea that would be fine just scotch it back make sure no shiny places, any scratches or chips you might wanna sand so they blend in but other than that yea a scotch pad is fine I'm doin mine at the...
  9. Replies
    4
    Views
    223

    Ah ok so I'd want L jetro for my set up wouldn't i

    Ah ok so I'd want L jetro for my set up wouldn't i
  10. Replies
    22
    Views
    1,044

    I would give you videos but my cars engine is in...

    I would give you videos but my cars engine is in pieces at the moment might be able to sort a video of my mates car for you, neither go above the legal limit with the silencers (boxes) they come with...
  11. Replies
    4
    Views
    223

    With the power FC what's the difference between...

    With the power FC what's the difference between the 2 'Jetros' they do?
  12. Replies
    22
    Views
    1,044

    The blitz nur spec isn't above legal Db rate to...

    The blitz nur spec isn't above legal Db rate to my knowledge pal my mates got one on his s14a

    His was loud but he took centre box out, is de-catted and 3'' downpipe and manifold I've got a apex...
  13. Replies
    4
    Views
    223

    Potential turbo swap stage 3a...

    Hello all,

    I have a s14a stage3a horsham board on my ecu, my question is with me having a GT2871r at the minute, could I swap the turbo to a different one like GTX2863r or GT3071r without having...
  14. Replies
    4
    Views
    459

    Defo wh it is loom is in drivers side wheel arch...

    Defo wh it is loom is in drivers side wheel arch see it on a lot of s14/a's worn areas need to take wing off and you will see loom below piece of metal stuck out relocate look above and you'll be...
  15. Mines a decatted apex one that's loud enough...

    Mines a decatted apex one that's loud enough without exceeding 100Db
  16. You can loosen the bolts (2 each side) the go up...

    You can loosen the bolts (2 each side) the go up from bumper into the wing and then you will be able to access the two bolts from wing into body
  17. Thread: Gt2871r

    by d-lo_200sx
    Replies
    1
    Views
    314

    If you keeping the turbo bottom mounted and you...

    If you keeping the turbo bottom mounted and you have already swapped from stock to braided then you won't need to change them, the turbo should come with a new actuator anyway so you won't need to...
  18. Replies
    42
    Views
    2,322

    My system is apex and it's quite loud IMO if your...

    My system is apex and it's quite loud IMO if your looking for something quiet, like a few others have said the no good oval system might be your best bet or maybe look into a custom made system not...
  19. Replies
    1
    Views
    3,575

    What was it fully comp mate? I'm with them on my...

    What was it fully comp mate? I'm with them on my 14a mods declared (stage3a) Manchester area 690 quid which I thinks awesome considering Manchester higher risk postcodes generally
  20. Replies
    2
    Views
    250

    Have you tried using another idle control valve...

    Have you tried using another idle control valve just to do process of elimination?
  21. Replies
    4
    Views
    406

    Sorry I couldn't get on the site, had a lot of...

    Sorry I couldn't get on the site, had a lot of personal things to deal with, one of which was one of my closest friends died in a car accident.

    I do have a catch can but it is one where it doesn't...
  22. Replies
    4
    Views
    406

    Oil in Intercooler pipe

    Hey guys

    Currently running a gt2871r (hks version) and it's top mounted to the sr20det s14a, doing some engine bay painting and noticed when I removed turbo that there was about 3-5 teaspoons of...
  23. Replies
    2
    Views
    846

    Image not working mate, upload with photobucket...

    Image not working mate, upload with photobucket then copy the html code version into the box where you type ya messages on here
  24. Just pinch it with your index finger and thumb...

    Just pinch it with your index finger and thumb the hold ya hand in the air and squint one eye to accurately meausure it that way��
  25. I no someone use a chinese turbo t3/t4 at 12psi...

    I no someone use a chinese turbo t3/t4 at 12psi for 4 years now on his audi never missed a beat, but on the other hand I've also known of a friend of a friend who used a eBay Chinese turbo and within...
Results 1 to 25 of 247
Page 1 of 10 1 2 3 4