Search:

Type: Posts; User: pointz

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Replies
    5
    Views
    96

    Do a pressure test on the intercooler and...

    Do a pressure test on the intercooler and pipework, these cars are 30 years old the intercoolers are prone to leaking.

    No knock isn't from bad afr necessarily

    Sent from my SM-G960F using...
  2. Replies
    5
    Views
    96

    You're running 0.9bar of boost through the stock...

    You're running 0.9bar of boost through the stock small turbo, its going to drop off.

    Get a t28 or t28r on it, bin the likely leaking intercooler and get a tune.

    Afr may look fine but does your...
  3. 2871r is a straight swap just may have to rotate...

    2871r is a straight swap just may have to rotate the core slightly. Pm jay1017 he has a hybrid 2871r for sale freshly built.

    If going standalone most standalone ecus have the capability to control...
  4. Thread: ca18 problems

    by pointz
    Replies
    5
    Views
    205

    Check/clean breather hardline between block and...

    Check/clean breather hardline between block and inlet cam cover.

    Common issue that can result in dipstick popping out and will cause bearing wear

    Sent from my SM-G960F using Tapatalk
  5. Replies
    13
    Views
    244

    I'm running a 1.6mm cometic so can't go back to...

    I'm running a 1.6mm cometic so can't go back to oem unfortunately

    Sent from my SM-G960F using Tapatalk
  6. Replies
    13
    Views
    244

    Any opinions on this?

    Any opinions on this?
  7. I have just restored an s13 on a metal rollover...

    I have just restored an s13 on a metal rollover jig, and from that experience I would definitely not rely on a jig made from timber and I'm a carpenter by trade.


    Weigh up the cost of buying the...
  8. You can get a rollover jig for ~300 on ebay that...

    You can get a rollover jig for ~300 on ebay that are more than capable.

    I had one in my single garage smaller than the dimensions you note above.
  9. Replies
    3
    Views
    165

    Yes auto ecu will work in manual car. As long...

    Yes auto ecu will work in manual car.

    As long as if its lambda car the ecu is 39fxx and 3 pin maf

    Or

    Non lambda 44fxx ecu 4 pin maf


    Sent from my SM-G960F using Tapatalk
  10. Replies
    13
    Views
    244

    Removed the head and looks as though it has...

    Removed the head and looks as though it has blowby on all 4 at some point.

    Opinions?

    Bad gasket, headlift, stud...
  11. Replies
    13
    Views
    244

    Yes as stated aftermarket reservoir which is the...

    Yes as stated aftermarket reservoir which is the same size as stock one.

    I have been looking at well seal
  12. Replies
    13
    Views
    244

    Its your old head which had a cleaning skim to...

    Its your old head which had a cleaning skim to achieve the correct finish that cometic specify but my block.

    R3k1355 it seems to do it while street driving too.
  13. Replies
    13
    Views
    244

    Coolant and pas issues

    I've built and had my forged ca mapped running 1.4bar low boost and 1.8bar high boost, took it on a trackday and noticed it pushing coolant out the expansion, not massive amounts.

    I have...
  14. Thread: Best Tyres?

    by pointz
    Replies
    43
    Views
    775

    Get a decent alignment or at least your alignment...

    Get a decent alignment or at least your alignment checked, i have just fitted Michelin pilot sport 4 on the back of mine with 400ish bhp and they're amazing so far.
  15. Replies
    23
    Views
    6,475

    Gay

    Gay
  16. Replies
    9
    Views
    301

    Give it a go yourself, if you have a unit and...

    Give it a go yourself, if you have a unit and compressor etc just take your time with prep
  17. Replies
    0
    Views
    136

    Red s15 Southampton

    Seen a few times now specifically around town and northam, bitterne area.

    Anyone here
  18. Replies
    12
    Views
    335

    Tooth out on timing belt, don't rely too much on...

    Tooth out on timing belt, don't rely too much on the timing marks on the backplate, focus more on counting the teeth (39 between cam dots, 48 between exh cam and crank dot.)
  19. Replies
    0
    Views
    162

    Abingdon airfield trackday 16th oct

    Anyone else fancy coming along? Few of us are booked on, still a handful of spaces left!

    Link for booking-

    https://www.motorsport-events.com/products/16-october-2020-abingdon-track-day
  20. Replies
    184
    Views
    89,545

    Bumping up an old thread to see more recent power...

    Bumping up an old thread to see more recent power figures :thumbs:
  21. Thread: Trax 2018

    by pointz
    Replies
    6
    Views
    3,073

    Believe there would of been a stand for japfest...

    Believe there would of been a stand for japfest but they have been combined so its basically just trax.
  22. Replies
    15
    Views
    704

    Bcpr6es for stock power :thumbs:

    Bcpr6es for stock power :thumbs:
  23. Replies
    4
    Views
    2,175

    No nonsense degreaser from screwfix has been the...

    No nonsense degreaser from screwfix has been the best for price I have found
  24. Replies
    10
    Views
    507

    I'd charge the battery. Check the terminal...

    I'd charge the battery. Check the terminal connections on the battery and main ground wires.

    Had so many jump leads make a shite connection that nothing happens.
  25. Replies
    35
    Views
    2,717

    Your inbox is full Ash :thumbs:

    Your inbox is full Ash :thumbs:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4