https://uploads.tapatalk-cdn.com/201...4459e0059b.jpg
Sent from my iPhone using Tapatalk
Printable View
https://uploads.tapatalk-cdn.com/201...4459e0059b.jpg
Sent from my iPhone using Tapatalk
Also found that 350z coils fit the VE rocker cover and have the same plugs as S14a ones. Slightly longer than the original sr20 ones but not too big an issue.
Unsure how these compare to VAG etc but no need for another wiring loom.
https://uploads.tapatalk-cdn.com/201...9deb70fbe2.jpg
Sent from my iPhone using Tapatalk
Ha, how’s the ghetto de-t drive?
Just like a DET so far [emoji23] still needs to be tuned so not pushed it yet
Sent from my iPhone using Tapatalk
Good to see it going.
id be tempted to just run the De+T on a generic chip. unless you can get it mapped cheap. I know the compression ratio is higher but most unopened SR's are knackered so its not going to be far off what a healthy one was back in the olden days when generic chips were mapped. just try not to kill the crank.
Long time since i've updated this, finally got this almost done
https://uploads.tapatalk-cdn.com/202...a0320a0616.jpg
Sent from my iPhone using Tapatalk
Ooooh wow, would you look at that. Very interested to see this go. I would love to put a VVL in my new one, but I can't at all justify it because of what I'm asking of the car which is not a lot. Super interested to see this finished!
It’s been a long haul, It’s running now just sorting a base tune on it.
I’ve spent a lot of money and to be honest I don’t think I’d do it again. But yes it should hopefully go well.
In interested to see how long the gearbox lasts lol
Sent from my iPhone using Tapatalk
starting to look a bit more complete, a few small jobs to finish on the engine but its running well, cant wait for all this lockdown to be over so i can actually get it to the dyno, im sure everyone is the same, but the more time i get the more i seem to remove from the car.
https://live.staticflickr.com/65535/...97b2204561.jpgSR20VET running by John Johnstone, on Flickr
Looks alright I suppose....
Love it mate, great work.
Mines not been on track since the Sxoc weekender at blyton park and I killed the engine :D
I want your engine [emoji23]
Sent from my VOG-L09 using Tapatalk
https://uploads.tapatalk-cdn.com/202...27d53f6f52.jpg
Finally back on the road, car has been behaving so far, got around 100miles on it so far, I’ll maybe do 500 then drop the oil and get it on a dyno.
Sent from my iPhone using Tapatalk
https://uploads.tapatalk-cdn.com/202...f6381c3959.jpg
Finally got the seat sitting sitting where I needed/wanted it to be.
https://uploads.tapatalk-cdn.com/202...7ccfae1da8.jpg
Also moved the wastegate on the manifold, had to make a link pipe so I had more room for everything.
https://uploads.tapatalk-cdn.com/202...15c673fb6b.jpg
Turbo side as it sits
https://uploads.tapatalk-cdn.com/202...e31b20eb4e.jpg
Sent from my iPhone using Tapatalk
Love the seat rail mate
Finally got some sort of success after a long time.
https://uploads.tapatalk-cdn.com/202...80881a6dc3.jpg
https://uploads.tapatalk-cdn.com/202...75f761b9a8.jpg
Also got a new dash centre panel which tidied up the interior pretty well.
https://uploads.tapatalk-cdn.com/202...f7c1dbda32.jpg
Next up is a gearbox conversion and a clutch, but likely going to be into next year now.
Sent from my iPhone using Tapatalk