View Full Version : my project RB200
Ive just started work on my s13 the plan is to fully strip it and fit an RB25 DET lump firstly im goin to trial fit the engine and that and get it running so i can sort out the body work then it will come out again for a full rebuild im undecided on spec and such will worry about that wen it comes to it: This will include detailed pics on how the conversion is done everything you need and also prices for those of you who are thinking of doing it yourselves.
http://i200.photobucket.com/albums/aa192/rb200/Picture024.jpg
this is the base car i got it for £350 off of ebay, taxed and tested.
http://i200.photobucket.com/albums/aa192/rb200/Picture044.jpg
i took the engine and gearbox straight out.
http://i200.photobucket.com/albums/aa192/rb200/Picture056.jpg
pic ere with the cross member removed i left steering rack on and supported it with an axle stand,
http://i200.photobucket.com/albums/aa192/rb200/Picture059.jpg
wings off
http://i200.photobucket.com/albums/aa192/rb200/Picture060.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture061.jpg
theres bit rust ere later cut it out and got some sheet metal ready to weld it up,
http://i200.photobucket.com/albums/aa192/rb200/Picture064.jpg
slight surface rust round the front nothin bad,
http://i200.photobucket.com/albums/aa192/rb200/Picture065.jpg
i cut out the battery tray needs some tidying up
http://i200.photobucket.com/albums/aa192/rb200/Picture066.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture067.jpg
its rusted through ere looks like it been done before but they made a bad job of it,
http://i200.photobucket.com/albums/aa192/rb200/Picture070.jpg
so ive stripped most bit out of the bay now and started taking it back to bare metal
http://i200.photobucket.com/albums/aa192/rb200/Picture071.jpg
took me ages to get this far
http://i200.photobucket.com/albums/aa192/rb200/Picture073.jpg
looks good in bare metal
http://i200.photobucket.com/albums/aa192/rb200/Picture072.jpg
started on the bulk head ive also knocked it back and up abit around gearbox tunnel just to make it more easy to fit the RB gearbox ,
over last few days ive taken off a few more parts and started on the front taking it back to bare metal its such a time consuming job,
the plan is to strip it all stitch weld the chassis and prime it over the next week or so,
ive got my R33 GTST cross member hoping to send that off for shotblasting and powder coating i will put more pics up asap,
My loom has been sent upto buffy so he can wrk his magic,
and this is the biuld so far only took a week or so to get this far thats working on her after i get home from wrk hope u all enjoy
heres some more pics of her this is now with the lights off
http://i200.photobucket.com/albums/aa192/rb200/Picture074.jpg
heres the s13 loom its been sent off to buffy along with the r33 loom ill take some pics wen i get it back and show you the differance
http://i200.photobucket.com/albums/aa192/rb200/Picture063.jpg
heres the skyline cross member its goin to be shot blasted and then powder coated
http://i200.photobucket.com/albums/aa192/rb200/Picture076.jpg
got this also off of ebay super mini tt
http://i200.photobucket.com/albums/aa192/rb200/Picture075.jpg
and ive also got these lights once the project gets that far the halo angel lights
http://i200.photobucket.com/albums/aa192/rb200/Picture077.jpg
not been able to do much so far this bank holiday coz of the weather :mad:
The_BULK
26-05-2007, 23:05
good luck with this mate :thumbs:
Swedish Mike
26-05-2007, 23:08
Looks good! You should move this to the project forum.
mattkeeber
26-05-2007, 23:16
Looks good! You should move this to the project forum.
You need to be a paid member to have a thread in that section :thumbs:
Looking good! :D Where about's in Notts are you?
Hey guys just waiting to transfer funds to my paypal account then ill be a full member hopeful in nxt week or so, im near mansfield mate :)
Well its crap weather 2day so not beable 2 do anythin again :mad: :mad:
The weathers ok 2day so ill be doin abit more ill post pics up of update:wave:
dannyb1986
28-05-2007, 11:45
iam only in alfreotn mate, not far from you !
kool sounds gd if i ever need a hand lol (cheeky) ive never seen another s13 round ere :(
what you using to take the paint off the engine bay??
dannyb1986
28-05-2007, 17:18
theres a lad near me thats building a beast off a s13, around 500bhp he will be going for. anoher lad has a s14a aswell. i dont know anyone from mansfield who has one though! as said above what are you using to remove the paint?
Hi mate well im in selston i say mansfield way coz no1 ever knows where selston is,
im using a light sand paper 2 take off the paint hard enough to get it off but only enough just to make the metal slightly ruff so primer sticks to it ive got some more done ill post some pics up asap:wave:
well managed to get little bit more done last day or so not much though due to the weather
http://i200.photobucket.com/albums/aa192/rb200/Picture082.jpg
got most the front done started on bulk head and the other side also took off master cylinder and brake servo,
http://i200.photobucket.com/albums/aa192/rb200/Picture083.jpg
just got to get the little bits n bobs off then its ready for welding
anyone in nottinghamshire or derbyshire with a welder that wouldnt mind helpin me out would be great:thumbs:
well this all ive got done hope to get rest done in bay remove rear subframe nxt few days if the weather holds up:wave:
Thanks to the good weather today ive got abit more done
i decided to rent out a welder for the weekend ive started to stitch weld the engine bay
http://i200.photobucket.com/albums/aa192/rb200/Picture087.jpg
im goin to put a few more welds in between the gaps
http://i200.photobucket.com/albums/aa192/rb200/Picture088.jpg
welded new plate in ere as the last one was rusted
http://i200.photobucket.com/albums/aa192/rb200/Picture089.jpg
got most of it done now just some bits ive got to do by hand as i couldnt get in with th drill
http://i200.photobucket.com/albums/aa192/rb200/Picture090.jpg
i put temp primer on the welds to stop them rusting it will all be removed when i come to spray it properly
http://i200.photobucket.com/albums/aa192/rb200/Picture091.jpg
also started to strip the skyline crossmember
http://i200.photobucket.com/albums/aa192/rb200/Picture092.jpg
all going well tomorow ill weld the rest i get the rest sanded down, im just waiting for my compresser to come then i will beable to spray it, im also going to strip the inner archer and put new underseal on. :D
great weather today so i cracked on some more i managed to remove the rear subframe
http://i200.photobucket.com/albums/aa192/rb200/Picture002.jpg
i couldnt seem to get the nuts off of the prop so left it on
http://i200.photobucket.com/albums/aa192/rb200/Picture003.jpg
the underside is solid with ony surface rust,
http://i200.photobucket.com/albums/aa192/rb200/Picture004.jpg
chassis rails are all solid
http://i200.photobucket.com/albums/aa192/rb200/Picture005.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture006.jpg
this is the front drivers arch its rusted right through
http://i200.photobucket.com/albums/aa192/rb200/Picture007.jpg
this is it so far just the start lol:eek:
Come on guys i feel like im talkin to myself
IIvIIitch
03-06-2007, 19:55
i'll have to pop up one day to take a look/give a hand with anything needed :thumbs:
i'll have to pop up one day to take a look/give a hand with anything needed :thumbs:
cheers mate i wanna strip the inside soon u can have your seat and carpet then :D
IIvIIitch
03-06-2007, 20:06
i'll come give you a hand to do that, its a nice simple job that cant go wrong :wack:
colchester daz
03-06-2007, 20:06
Good stuff mate, i'll be doing mine soon, in one of your first post's you put that you sent you standard and 33 loom to buffy, Does he do a bit of loom work?
yep he sure does hes a wiz with the looms drop me a pm and ill give you his no. you can ask him :D
colchester daz
03-06-2007, 20:48
yer cool thanks mate , i'm trying to do all the homework first because i dont want my car off the road to long, so any other help will be fantastic.
best thing to do if u want it done quickly is get everythin before hand plan exactly how u want the car before this way u not get stuck whilst building it, many people have done it now so if needed theres lots of advice available along the way :D
Been busy today IIvIIitch came and helped me he stripped out the interior
http://i200.photobucket.com/albums/aa192/rb200/Picture004-1.jpg
all seat and carpet are out just got to remove all the sound deadening,
http://i200.photobucket.com/albums/aa192/rb200/Picture005-1.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture007-1.jpg
we also made a start on this,
http://i200.photobucket.com/albums/aa192/rb200/Picture006-1.jpg
started to cut the spare wheel out just need to trim it off and make up a template for the sheet metal, then it will be ready for a new fuel tank,
Also remove all fuel lines and brake lines,
This is it so far plenty more to come :D :wave:
IIvIIitch
06-06-2007, 23:08
Starting to look very bare indeed :thumbs:
Starting to look very bare indeed :thumbs:
yep a little bit im thinkin of putting the spare wheel back in lol :rolleyes:
me and IIvIIitch have been busy today again, we removed the dash all interior panels have now been removed :D
http://i200.photobucket.com/albums/aa192/rb200/Picture008.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture009.jpg
ill be fabricating a dash out sheet metal,
http://i200.photobucket.com/albums/aa192/rb200/Picture010.jpg
hoping to go with a carbon roof
http://i200.photobucket.com/albums/aa192/rb200/Picture011.jpg
ill be strippin back to bare metal and stich welding the inside
http://i200.photobucket.com/albums/aa192/rb200/Picture012.jpg
so nearly everythink is stripped now so its time for the rebuild, watch this space as i will be doin a detaild account on how to put the car back together and put in a RB engine :D :D
IIvIIitch
07-06-2007, 23:46
I've never seen anyone look so worried while i was remove the alarm :wack:
lol yh yh i was fine :eek:
well got abit more done this weekend started to strip the paint from the inside all the sound deadening has been chipped up(well nearly) ill post some pics up soon :D
well ive been real busy 2day everything is stripped inside now apart from loom and steering wheel
http://i200.photobucket.com/albums/aa192/rb200/Picture009-1.jpg
i also cut the rest of the rear end out
http://i200.photobucket.com/albums/aa192/rb200/Picture004-2.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture003-2.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture002-2.jpg
i peeled it all back off of the rivets to end up with this
http://i200.photobucket.com/albums/aa192/rb200/Picture006-2.jpg
i cut the back out also
http://i200.photobucket.com/albums/aa192/rb200/Picture005-2.jpg
this all took ages i then started removing the paint from the inside
http://i200.photobucket.com/albums/aa192/rb200/Picture010-1.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture011-1.jpg
this is the bar that goes across the dash ive started to buff it up as there was alot of surface rust on it
http://i200.photobucket.com/albums/aa192/rb200/Picture008-1.jpg
this is what ive been doin all day
I mite aswell talk to myself lol :whip:
skyshack
18-06-2007, 22:18
I mite aswell talk to myself lol :whip:909 views says your very wrong. Threads like this really don't need a lot of clutter in them and you are doing alright.
why is there soo much cutting out needed in the rear end??
oh yea kep up the good work ill defo be folling this.
909 views says your very wrong. Threads like this really don't need a lot of clutter in them and you are doing alright.
skyshack is right but I am going to clutter it up :D
Firstly some questions :)
Why are you stripping the paint off everywhere? I would have thought that some areas, the bulkhead for example, don’t need to be stripped back to bare metal?
Like myself, I see you are working outside and it’s not easy :no: how are you going to stop everything rusting with so much bare metal exposed?
How are you going to fettle the rust where the chassis leg meets the inner wing?
http://i200.photobucket.com/albums/aa192/rb200/Picture066.jpg
Fantastic project with superb pics :thumbs: I will be watching with great interest :)
Pics like this are invaluable :notworthy
http://i200.photobucket.com/albums/aa192/rb200/Picture004-2.jpg
It gives us a good idea of the condition inside the chassis legs. I intend to wax inject our S13 now – but I won’t be using waxoyl
Keep up the good work :thumbs:
McRearout
20-06-2007, 10:43
Great work, i'll be watching with interest :)
HI peeps firstly thanks for all the nice comments :D
ive stripped everthink back 2 bare metal as i want to repaint everything i can so it all like new as most parts will also be new or cleaned up, i got the rust off the chassis leg where it meets the inner wing with a wire brush on a drill these are great then used sand paper for the little bits.
As for the cutting of the rear ive cut it back as ill be welding in a piece of sheet metal to house the new in car fuel tank, after removing the metal i found alot of surface rust but nothin major, its unbelivable where water gets trapped and bits you didnt think would rust start to.:(
If anyone wants any specific photos of anything let me know or if you want any advice, ive just got my deox jel today so will start removin some rust :D
dannyb1986
22-06-2007, 22:35
hi mate why have you cut that much of the floor out? also if you need a hand give me a shout! ill come and help! iam a mechanic aswell
hi mate why have you cut that much of the floor out? also if you need a hand give me a shout! ill come and help! iam a mechanic aswell
Hi ive cut out so much as ill be welding in a new metal sheet for the floor to house the new in car ally fuel tank, cuttin out so much will now give the new floor more support and also renew old rusted parts, buffy did the same with project phoenix,
Thanks for the offer ill give you a shout when i need some help most just cleaning parts up and that at the min, i just need a welder now :D
Hi ive cut out so much as ill be welding in a new metal sheet for the floor to house the new in car ally fuel tank, cuttin out so much will now give the new floor more support and also renew old rusted parts, buffy did the same with project phoenix,
Thanks for the offer ill give you a shout when i need some help most just cleaning parts up and that at the min, i just need a welder now :D
Mr Tone inspired then eh? :)
Watching with interest :thumbs:
Dave
Yea i was thinking about putting a fuel tank in the back anyway before i seen his thread but didnt know the best way to go about it when i seen his thread it seemed the perfect way, took ages thought to cut out lol :(
I bet it did dude - good project anyway :)
dannyb1986
23-06-2007, 11:44
i cant weld very good, but i could probably get a welder for the weekend
Ive done a bit more today took the rest of the parts off the front end
http://i200.photobucket.com/albums/aa192/rb200/Picture002-3.jpg
as you can see in the nxt pic the brake dust sheilds have almost rusted away
http://i200.photobucket.com/albums/aa192/rb200/Picture003-3.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture004-4.jpg
i want to convert over to 5 stud so can i replace the part arrowed with a skyline one will it just bolt straight into the suspension and lower arm or is the skline one differnt?
http://i200.photobucket.com/albums/aa192/rb200/Picture005-3.jpg
this is all crap from my shed thats now been skipped
http://i200.photobucket.com/albums/aa192/rb200/Picture006-3.jpg
the inner arches are in good condition
http://i200.photobucket.com/albums/aa192/rb200/Picture001-3.jpg
used some deox c on these nuts and bolts
http://i200.photobucket.com/albums/aa192/rb200/Picture-1.jpg
this is how they came up
anyone who wants to come round and help is more than welcome to lol :thumbs:
bemmerkid
23-06-2007, 18:37
Sweeet!! im doing my Rb swap some time this week ill also do a write up.
but theres a few bits i dont understand and may get stuck on so if any one local to me wanna give a hand it will be appreciated.
what else of the skyline fits the s13?
rb did you get a full skyline?
what parts you going to use from it?
have you found any problems so far?
im doing my loom myself as im good with wires,lol
how come you bare metal-ed it all? cant you just treat the rustey areas?
i take it you removed the spare wheel hole to save on weight instead of welding a plate over it?
i think your doing a wicked job there and if you was closer i would come help ya.
ill be watching this space!!
can you pm me your msn address so i can ask questions on the way on ur build to save cluttering up your project page.
cheers
cheers mate outlawz_makaveli1@hotmail.com
ive cut the spare wheel out and im goin to weld in a sheet of metal this will house the in car ally fuel tank
dannyb1986
23-06-2007, 20:47
you doing anything to it next saturday? i may be free, not a 100% sure but i dont mind coming up and helping out!
more than likely lol out there when ever the weather lets me :D
turbotomo2oosx
01-07-2007, 15:13
looking good pal. will be watching with wide eyes. good luck! :)
looking good pal. will be watching with wide eyes. good luck! :)
Cheers mate weathers getting on my nerves ive now stripped most if the underseal from underneath so it ready for shotblasting, pics to follow
dannyb1986
03-07-2007, 19:53
have you got a compressor yet, havent had chance to speak to my mate yet. iam just in the middle of doing the 5 stud conversion, why do you want to use the skyline knuckles? also ive just bought some mood ball joints for £40! :thumbs:
Hi danny yep got a compressor on friday, i was just looking at differnt options on converting to 5 stud, i cnt get the split pins out front the ball joints n that either:(
dannyb1986
03-07-2007, 21:15
easy, get some sidecuts and chop them off, then air gun the nut up, then get a small punch and knock them out! there easy enough. ill have go if you get properly stuck! iam using the s14 knuckls
cheers mate just got to get and air rachet now
turbotomo2oosx
05-07-2007, 13:08
was this your day to day car befor you started work on it? or did you buy it to do just this? an yea some summer were havin init :annoyed:
was this your day to day car befor you started work on it? or did you buy it to do just this? an yea some summer were havin init :annoyed:
yea this was my day to day car so ive got nothing at the min, progress is slow at min due to the crappy weather i was hoping to have more done but ive now caught the lazy bug lol :rolleyes:
ive stripped the underseal from the underside just got to shot blast it and it will be ready for painting and sealing
turbotomo2oosx
06-07-2007, 18:37
i planed on rebuilding my first one but when i stared driving it i didnt have the heart to take it off the road and strip it. so i have bourght another one to play around with befor i fall in love with it lol :wack: your doing well im sure it will be mint when its dun. worth the wate! have you got the rb to go init or still wateing for it? if you got it, lets see some pics :nod:
No im waiting to buy the engine till more or less last as i know if i buy it now id be so tempted cut corners here and there to hurry and get it in lol, this way i can make sure everything else is perfect ready for the engine,
im ordering my primer for the floor and arches but im not sure whats best to go for obviously i need something weather proof and hard wearing to protect from the road ect so if anyone has any ideas let me know, ill also need something to seal it after.
Best really depends upon preparation standards. If its perfect then a 2K primer followed by a 2K epoxy mastic will offer the best protection though the finish will be a compromise, epoxy mastic dries satin.
If there’s any rust at all then I would go for a zinc rich primer followed by either epoxy mastic or a full gloss 2K. Then there’s the POR stuff but I know very little about that. Regardless of what you use I would still spray some stonechip over the top but you need to be careful, It’s not a good idea to use stonechip where anything is fastened to the shell. I will be posting pics up in my thread of how to do this.
I have 5L of epoxy mastic that I don’t need. I went for the shiny full gloss stuff. PM me if you are interested.
Keep up the good work and keep those pics coming :thumbs:
Edit: What size of compressor did you buy and did it run the blast gun OK?
i got 2hp 50litre tank it runs the shotblaster so well, ive just order some epoxy mastic chassis pack, will i need to put a primer on before applying this? as it says it can go straigh onto bare metal, i would of brought urs didnt see the post in time :cry: ,
ill be posting pics up soon there will be not rust before i apply the primer im getting rid of it all :nod: i get my welder 2moro so progress should be full steam ahead again :thumbs:
well not really done much lately been being lazy but heres what i have done:
http://i200.photobucket.com/albums/aa192/rb200/Picture007-3.jpg
started stripping the arches this is the drivers side found abit of rust around the seams
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture008-2.jpg
it had rusted right through in one part
ive now nearly stripped all the underseal off these are the only places there were rust
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture010-2.jpg
where the subby bolts to the floor
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture011-2.jpg
same on both sides
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture016.jpg
other than that the body is solid underneath
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture017.jpg
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture015.jpg
both rear arches are fine
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture012-1.jpg
then this little lot came 2day that will be £250
http://s200.photobucket.com/albums/aa192/rb200/?action=view¤t=Picture014.jpg
these are primers for the floor 92% epoxy zinc, epoxy 121 chassis pack,4942 stone chip and also some seam sealant,
ill be shotblasting all underneath this weekend aswell as stitch welding the entire shell aswell as some other things
well not really done much lately been being lazy but heres what i have done:
http://i200.photobucket.com/albums/aa192/rb200/Picture007-3.jpg
started stripping the arches this is the drivers side found abit of rust around the seams
http://i200.photobucket.com/albums/aa192/rb200/Picture008-2.jpg
it had rusted right through in one part
ive now nearly stripped all the underseal off these are the only places there were rust
http://i200.photobucket.com/albums/aa192/rb200/Picture010-2.jpg
where the subby bolts to the floor
http://i200.photobucket.com/albums/aa192/rb200/Picture011-2.jpg
same on both sides
http://i200.photobucket.com/albums/aa192/rb200/Picture016.jpg
other than that the body is solid underneath
http://i200.photobucket.com/albums/aa192/rb200/Picture017.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture015.jpg
both rear arches are fine
http://i200.photobucket.com/albums/aa192/rb200/Picture012-1.jpg
then this little lot came 2day that will be £250
http://i200.photobucket.com/albums/aa192/rb200/Picture014.jpg
these are primers for the floor 92% epoxy zinc, epoxy 121 chassis pack,4942 stone chip and also some seam sealant,
ill be shotblasting all underneath this weekend aswell as stitch welding the entire shell aswell as some other things
20L :eek: are you doing the top in epoxy paint and all? :D
Good work fella :thumbs:
i dint mean 2 order that much lol ill be doing underneath all for arches engine bay, then maybe inside 2, just got to shotblast now cnt wait:thumbs:
turbotomo2oosx
28-07-2007, 21:59
update?
hi ive done nothin really past cple of weeks, been doin bits n bobs on other peoples cars, ive orderd the metal to weld up the back end, ill stitch weld the whole car and get in sprayed underneath asap :thumbs:
this is an awesome project dude, i love seein stuff like this, keep up the good work, looks great:thumbs:
cheers mate they'll be an update soon :thumbs:
This is a really cool project mate:nod: :thumbs:
I will be watching this with serious intrest:notworthy
p.s do you want another to do when you finished;) :p
Keep up the good work buddy:clap:
This is a really cool project mate:nod: :thumbs:
I will be watching this with serious intrest:notworthy
p.s do you want another to do when you finished;) :p
Keep up the good work buddy:clap:
Yep give me a ring when you want it doing lol,:smash:
IIvIIitch
02-08-2007, 08:02
oi, mine first :wack:
oi, mine first :wack:
lol What do you want doing now, if i charged you it would pay for my project:whip: :thumbs:
We all want it done :D
Hardest bit so far is finding a salvage GTS-T :cry:
We all want it done :D
Hardest bit so far is finding a salvage GTS-T :cry:
are you doing it urself mate?
Plan to once ive got a donor car.
So much more rewarding I think :)
Yh its great busy on mine at min ill be welding the back up and stitch welding the whole car start of nxt week :D
excellent work! :)
cheers hope to get alot of pics up some time nxt week so stay tuned
Hey heres a little update, i got my sheet of metal today,
so i started by making this,
http://i200.photobucket.com/albums/aa192/rb200/Picture025.jpg
i only used it to get the corners right once that was done i then put it onto the sheet,
http://i200.photobucket.com/albums/aa192/rb200/Picture019.jpg
i then cutted it out and trial fitted it,
http://i200.photobucket.com/albums/aa192/rb200/Picture021.jpg
needs about half a cm taken of to fit into the corner i perposly made it bigger so i had i little to play with,
http://i200.photobucket.com/albums/aa192/rb200/Picture022.jpg
top fits perfect
http://i200.photobucket.com/albums/aa192/rb200/Picture023.jpg
sides also fit perfect and flow with the arches,
http://i200.photobucket.com/albums/aa192/rb200/Picture024-1.jpg
here at the back ill cut out little strips of metal and join each 2gether,
well thats it for now thought id give u a little taster, lots more has been done ill post pics up soon:thumbs:
You could start your own car company...... building cars from scratch lol:D
great stuff though:)
You could start your own car company...... building cars from scratch lol:D
great stuff though:)
Cheers mate its very stressful getting everything just right lol :annoyed: :smash:
mindmineral
08-08-2007, 08:15
Its looking good! Keep it up bro - gives me sum inspiration!
Its looking good! Keep it up bro - gives me sum inspiration!
Cheers mate, its hard to see the end at the min lol i could do with some inspiration
little update the support bars have now been welded in
http://i200.photobucket.com/albums/aa192/rb200/Picture001-4.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture002-4.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture003-4.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture004-5.jpg
The floor is also welded in ill post pics up asap
Ok so heres some pics with the new boot floor in,
http://i200.photobucket.com/albums/aa192/rb200/Picture005-4.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture006-4.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture007-4.jpg
here i had to make up some plates to sit in the gap between the floor n body
http://i200.photobucket.com/albums/aa192/rb200/Picture009-3.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture008-3.jpg
sits perfect on the support bars,
http://i200.photobucket.com/albums/aa192/rb200/Picture010-3.jpg
this is the join line at the rear quite neat i think to say this is my first ever time at welding, all welds will be smoothed off so they will be hardly visable
IIvIIitch
15-08-2007, 14:45
really starting to take shape now bud, keep up the good work.
Nice work mate esp if it is your first time !
I worried about treating rust when I can hardly weld let alone cut huge bits out !
Nice work mate esp if it is your first time !
I worried about treating rust when I can hardly weld let alone cut huge bits out !
lol once it was cut out i wasnt really worried, ill be happy once its all smoothed off
just got my loom back heres some pics of it, theres 3 parts
main engine loom:
http://i200.photobucket.com/albums/aa192/rb200/Picture001-5.jpg
this i where its changed on the ecu end
the alternator loom
http://i200.photobucket.com/albums/aa192/rb200/Picture004-6.jpg
http://i200.photobucket.com/albums/aa192/rb200/Picture005-5.jpg
and knock sensor aac loom
http://i200.photobucket.com/albums/aa192/rb200/Picture003-5.jpg
Hows the project going mate
Keep up the good work
Hows the project going mate
Keep up the good work
yea its ok thanks mate alot slower than i had hoped but at least its moving forward, i just need underneath shotblasting so i can spray it thats the only thing thats holding everything up:annoyed:
Cool
Have you managed to source an engine?
Cool
Have you managed to source an engine?
theres a few about im leaving it though till ive got other bits sorted
park_monkey
21-08-2007, 21:56
Hi evryone, new to this oc:sxoc: there are some awesome projects on here, this one is something close to what i would like to do. does anyone know where i can get a list of the different models of skyline along with the engines they have and the different variations? i will be watching this thread closely, keep up the good work.:thumbs:
Hi evryone, new to this oc:sxoc: there are some awesome projects on here, this one is something close to what i would like to do. does anyone know where i can get a list of the different models of skyline along with the engines they have and the different variations? i will be watching this thread closely, keep up the good work.:thumbs:
Cheers mate, you can look on the skylineownersclub, there they will be able to give u the exact models: but here are some
r32 gtst came with rb20 det 2.0l turbo not sure if there was an n/a model
r32 gtr rb26 dett 2.6l straight 6 twin turbo
R33 gts 2.5l none turbo
R33 gtst 2.5l single turbo
R33 gtr 2.6 twin turbo
R34 gtt i belive this is a single turbo model
R34 gtr 2.6 twin turbo
Im not sure of the others but these are the main models you will come across:thumbs:
R34 gtt i belive this is a single turbo model
:nod: RB25DET Neo single turbo but with variable valve timing on both cams :)
Impressive project mate :thumbs:
cheers hope to get alot done over the bank holiday weekend
seb.racing
23-08-2007, 20:10
good:thumbs:
There was also R32 GT. 2.0L non turbo RB20E single cam as well.
Ivan
turbotomo2oosx
30-08-2007, 15:37
get much done over the weekend dude? made up your mind on the 4x4 idea? wont be easy but thatsnot the point isit. will be awesome if you can pull it off :thumbs: were you going to get it shotblasted to?
get much done over the weekend dude? made up your mind on the 4x4 idea? wont be easy but thatsnot the point isit. will be awesome if you can pull it off :thumbs: were you going to get it shotblasted to?
I think ill keep it rwd just because i wanna drift it, im shotblasting it myself, didnt get anything done i was working on another car all weekend a 200sx and ended up buying it lol:rolleyes:
turbotomo2oosx
30-08-2007, 19:21
nice :wack:
oh well goodluck with it dude. :thumbs:
nice :wack:
oh well goodluck with it dude. :thumbs:
Cheers dude got my grit orderd so as soon as it comes ill crack on with it this is only bit thats stopping me getting it rolling, soon as its blasted things should hopefully moving quickly
IIvIIitch
31-08-2007, 13:56
not now you have two sx's of your own and mine to work on :wack:
not now you have two sx's of your own and mine to work on :wack:
Well urs just might have to wait then lol :whip:
Hi mate
Have you got it blasted yet
Hows it going?
I think ill keep it rwd just because i wanna drift it, im shotblasting it myself, didnt get anything done i was working on another car all weekend a 200sx and ended up buying it lol:rolleyes:
IIRC the R32 4x4 gearbox was fine running just RWD, and needed only a fuse unplugging to get to work.
Remember hearing something about the R33/R34 boxes having a clutch style transfer box or something. Could be a load of goblers though and be fine as well.
i got my grit on wednesday n i have made a start i really want it done by the weekend so i can get first coat of primer on asap, ill post pics up as soon as its done
i got my grit on wednesday n i have made a start i really want it done by the weekend so i can get first coat of primer on asap, ill post pics up as soon as its done
I would "prime as you go" - blast as much as you can in a day and then prime it. Zinc primer dries pretty quick (under an hour) so there will be no probs with grit sticking to it when you start blasting again :thumbs:
I would "prime as you go" - blast as much as you can in a day and then prime it. Zinc primer dries pretty quick (under an hour) so there will be no probs with grit sticking to it when you start blasting again :thumbs:
Thanks for that mate i will do that then, hope to get most of it blasted tomorow:thumbs:
well bit of an update, i sent rb200 off for shotblasting last week had to hire a trailor n that, the company who was doing it quoted me £50-£100 to blast underneath and the engine bay and said nothing would be damaged in the process
he then rang me the monday an said they need to roll the car on its roof to blast it so it will damage all glass, he then said it will damage the car and wiring, the quote then jumped to £400, so i brought the car back home abit of a set back,
They also picked the car up with a fork truck and bent underneath also bending the seem of the floor pan.
So not to happy at the min such a waste of time it also cost me £160 to get it there n back for nothing :mad:
Anth4130
23-09-2007, 19:41
Oh sh*t :| the idiots :/
What are your plans on brake set-up?
What are your plans on brake set-up?[/QUOTE]
Im going to be using the k-sport 8pot brakes up front from apex :thumbs:
Powered by vBulletin® Version 4.2.3 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.