GreyDesigns - Sr20 S12 - Build

Powder Coating, and way too many photos.

This weekend I built my oven extension. Which ended up taking all day as clamping, drilling holes and riveting takes bloody ages! Was very satisfying to see it just pop together though, even if I would have rather welded it.

11017120_971335436242678_1779539702233791029_o.jpg


11236154_971335216242700_8682100167412736791_o.jpg


There were some holes at just the right height on the oven to hold the box nice and flush against the doors rubber seal. So I just have a bolt with some nuts stuck at a set distance and slot it in and push it down and that is it locked in place.

11539010_971334642909424_7218261074600445025_o.jpg


11731585_971334996242722_6376987693841393951_o.jpg


And here is the coated box. It is just tinfoil tape and some loft thermal lining.

11219485_971334196242802_9439046470672107_o.jpg


11055313_971333672909521_2186636782898790540_o.jpg


11110053_971333872909501_835934267404740012_o.jpg


11221499_971333426242879_7104690569100890468_o.jpg


Still needs a practical baking test to make sure the heat is even, and a bit more insulation as it can get very hot on the back wall. But the oven did get up to temp, so it is a step in the right direction. :D

The other thing I did was test out the powder for my rocker cover. The Red and white are exactly what I wanted, and the blue candy over chrome is pretty much there, applying it is hard though. I think I will order some more and do a few more tests before I commit fully, but I am pleased with how this came out with two coats. I might try and add some sparkles to the chrome base too...

11053529_971335016242720_8988531826853317453_o.jpg


11722227_971334286242793_5493098579146070446_o.jpg


11717479_971334042909484_6019159525113791755_o.jpg


11713738_971333189576236_4154265704800393393_o.jpg


11731951_971332872909601_5949152014712321885_o.jpg


11046221_971332862909602_7559096242956329305_o.jpg


Hopefully get the actual valve cover done next weekend :D
 
Rocker Cover Paint Started

I finally built up the courage to start on the rocker cover, I started by laying down and baking the red and white in two coats, then I covered the whole thing in chrome powder and dabbed off all the lettering. And it came out of the oven like this, honestly looks so great in person. Blew my mind when I took off the oven door.

Tonight I will try and lay the dark candy blue on the chrome, and hopefully not wreck it in the process! :D

11705339_974802202562668_4074795291634514946_n.jpg


11760291_974801702562718_4187093139481796001_n.jpg


10012534_974802019229353_141890954563907027_n.jpg


11695029_974802072562681_6063375413090749115_n.jpg


11760054_974802132562675_2850905611455281682_n.jpg


11707560_974802159229339_6229481212620175244_n.jpg
 
Last edited:
Well I tried to get it blue, but I didn't bake it in the end. I could see that it was going to look bad. So I cleaned it all off and will just keep it chrome for now.
 
I didn't get too much done this weekend as I was helping a friend powdercoat his rocker cover.

That said, I did manage to get the Frankenstein gearbox put together (CA box to SR bellhousing.) Very pleased that it ended up being pretty straight forward, though just a little bit fiddly. I think I will just spray it black and keep it simple.

11741150_977860942256794_3320556349954831400_o.jpg


I also got the baffles sealed back onto the cover, and the new rubber gaskets on. Still a few things to do here, but I am loving the way it looks atm, even if it isn't really what I had planned colour wise.

885746_977860695590152_5966528693231888949_o.jpg


11794053_977860708923484_3912125018218229119_o.jpg


11728886_977860712256817_8524530141847389572_o.jpg


I also got a small job off the list, and fitted the new release bearing, which was easy enough even without a press.

11053095_977860915590130_2231622057316717333_o.jpg



Good weekend. :thumbs:
 
Thanks guys, really pleased that you like it! :D And yes, engine bay is next on the list, a fair few holes to sort in it before paint though sadly. I will be going for the stock red I think. :)
 
Welder fixed, so I am now starting my attack on the front end rust to get it ready for paint.

Nice big hole on the drivers side arch that I didn't know about...

11951638_992458724130349_6815799623514079520_o.jpg


Battery tray out.

11930808_992469917462563_4857655069635339588_o.jpg


Most of the cuts made under the drivers side arch.

11930808_992469920795896_5819233961321407994_o.jpg


Haha, so much work to do, but it is a lot of fun hacking it up at least. :)

11930808_992469924129229_1527772796168625707_o.jpg


11930808_992469927462562_8686214568560242840_o.jpg


11930808_992469930795895_6434947733271937795_o.jpg
 
Got a fair bit of the welding done on the drivers side today. :)

I ended up cutting out a bit at the bottom of the turret too as I could see it was quite thin.

11958120_994424967267058_1990414046823452940_o.jpg

11894660_994424330600455_2347080185118655181_o.jpg


I need to find a way of clamping all these bits together so I can do the spot (plug) welds, and I will still need to grind back my ugly welds too. :sxoc:
 
Front end welding is done :D

I was made redundant so hadn't had much time to spare for the car (ironically,) because I have been working on my portfolio full time trying to train up to switch industry. But I took a week to put some time into the S12, so all the welding is done on the front now. I should be able to get paint this week and start getting it prepped next week. Feels nice to have made some progress again, I cant wait to actually drive it...some time in the future.

12196339_1025467160829505_8448642780057750682_n.jpg

12191584_1025466620829559_1546739760111139885_n.jpg

12234987_1025466424162912_3725496464916987162_n.jpg

12108170_1025466077496280_1600301534123953742_n.jpg

12208570_1025465260829695_3845779427942643394_n.jpg

12196366_1025466124162942_4070363480338547203_n.jpg

12208871_1025466654162889_6479130372562723104_n.jpg

12227694_1025466857496202_1131508161889540565_n.jpg

12239756_1025467080829513_6792506599062850644_n.jpg

12235133_1025465300829691_5751296395810276192_n.jpg

12190105_1025465910829630_3170878912090609832_n.jpg
 
Awesome progress. Nice to see your replicating the factory metal. Are you gonna re-spray the whole bay? same colour?

Thanks! And yeah, I am just waiting on paint now. So hopefully very soon, my shed gets very damp though, so I am limited by the weather. I really want to get it back on its feet and moved to my brothers house before next year (his new place has some incredible sheds and a four post lift, much better for welding sills!) I've just bought some old CS2 coilovers too, so I just need to sort out the rest of the front end geometry and then I should have all the parts I need, for now at least. :)
 
I had a couple of jobs to do that I had forgotten about, first up was to make some mounts for radiator. I used some 3mm steel and drilled 10mm holes to match the mounts on the Mishimoto. The welds are ugly but they will never be seen and are more than strong enough to have the radiator sitting pretty.

11986429_1031994073510147_6353128367954783665_n.jpg


And then I had a sheared bolt to extract from the chassis rail, I cant remember what it was for tbh, maybe subframe. Either way, it was a pita. I ended up building up a weldcicle™ and and then a welding a nut onto that and just wiggling it out at very low psi with the impact gun. Very easy to do the right way up. Upside down getting good enough penetration took 3 attempts. I'm chuffed it came out without having to use the drill of angle grinder though.

12294903_1031994116843476_7750442859722736106_n.jpg


And the result.

12274419_1031994040176817_21124365072086126_n.jpg


I've been gathering up all my paint supplies and buying up front end geometry too, so paint this week hopefully (weather dependent!):D
 
Time for a 2016 update me thinks!!!
I wish I had one; I have hardly been near it this year yet. Scotland was too wet and icy to get my painting done while I had the time. Still looking for a damn job too, haha, takes up more time than actually working...urgh, seeing my car unfinished is the worst! - 2016 will end better...
 
Well, it is painted now.

I decided not to update this until I finally got it painted, I was sick of rereading my "going to get this painted soon.." comments.

Anyway, I refurbished some s13 CS2s, and driftworks control arms, the rack and some other bits only got a quick rattle can job.

Engine bay painting went okay, after a fiasco with reacting paint that messed up really badly. But oh-well, finally red!

Unfortunately, I have now moved to Manchester (was in Aberdeen) so the car has been left up north. I will finish it, I just don't know how long it is going to take... :wave:

12961221_1111607818882105_5149092090144663827_o.jpg

12967988_1111607955548758_1900397689122692922_o.jpg

12957686_1111607952215425_5481994326904154897_o.jpg

12957528_1111608195548734_3841671613747827957_o.jpg

12977282_1111608288882058_1366411648701166173_o.jpg

12976796_1111608295548724_7584765134069424432_o.jpg
 
Back
Top