Green s14 zenki project!!

gus

New member
So I thought I'd start a project thread for the 14 as I've almost had it 2 years now 😂
It's lime green but a nice colour I think,
Basically stage 1a so 280hp ish

Here's a picture of shortly after I bought it.
https://i.imgur.com/UQNJjjS.jpg

In true a body fashion the first thing I did was.....
Fix it
https://i.imgur.com/https://i.imgur.com/xyLczOK.jpghttps://i.imgur.com/xyLczOK.jpg

As you can see, the fanny mould snapped clean off because it was a cheap eBay special (made of genuine chinesium no doubt)

I repaired that but have had ongoing issues since so it's now got a standard cast manifold on it.

The first mod I did was buy some wheels
Cosmis xt206r's in black chrome
18x9.5et11 with a 15mm spacer
18x11 et8 (turns out they don't fit under standard rolled arches 🙄)
https://i.imgur.com/00tJcp8.jpg
So I drove round with standard rear wheels on for ages.


The outside of the car hasn't changed too much yet, I plan on getting na an skirts and spats and going for a relatively clean low look.

I ended up swapping the cosmis for Rota Kyushas and cash my way.
https://i.imgur.com/JSTIRLD.jpg

I then swapped those for some xxr's (looked shit really)

Around this time last year I was driving to a friends house and the clutch pedal went to the floor, I thought it was slave/master related so I replaced both and bled it about 600 times with rich (pointz)
Still no clutch at all, it didn't slip or anything so it seemed weird!!
We thought the clutch fork could be ****ed so we took the box off and something was wrong straight away!!
https://i.imgur.com/LNz1xrO.jpg
Lots of muff attached to my pressure plate!!
Turns out what happened wasn't good!!
https://i.imgur.com/NkK7PK5.jpg
Basically my stage 2 rpc clutch had shat itself. I replaced with a stage 1 exedy clutch as I was recommended one and I didn't want a paddle clutch to annoy myself in traffic https://i.imgur.com/ikXvGhA.jpg


The car now has a corbeau drivers bucket with a driftworks super low rail, I like this seat a lot, it's maybe a bit firm on long journeys. Stuck a slam box wheel in as my old momo was ****ed.
https://i.imgur.com/SXgtfSH.jpg
I want a decent nardi now though tbh.

Got some white rota grids

Gayeee

https://i.imgur.com/IfWerxz.jpg

I then bought some drifworks cs2's as my old monopros had seen better days
They're very good and I'd recommend them tbh.
https://i.imgur.com/XLDucc5.jpg

Doge

https://i.imgur.com/gtL92tT.jpg

Went to the wheel alignment centre in southampton and got the car set up much better!! :)



https://i.imgur.com/tR1k0Hw.jpg

Ready for track time at jdm Combe :)
https://i.imgur.com/TkgpfsD.jpg

So the thread is basically up to date, I have re fitted zenki rear lights and fitted a number plate tilt bracket. I will update as I go along really. I plan on fitting a t28r and a proper exit at some point, also as I meant jones skirts and a few bits to make it have all the jdm points. Overall it's pretty tidy and I plan on keeping it that way. Thanks for reading if anyone read more than 3 lines of this!!
Any feedback is appreciated (except rich saying sr20's are gay 😂😂)
 
For some reason the images don't show, you'll have to click on them. Can't use photo bucket anymore as they want to charge money for 3rd party hosting now ��
If there's a better way of posting pictures let me know :D
 
i think i am going to use FLICKR mate, i just found the same thing, the first two years of build thread photos are now unable to be viewed :mad:
 
I'm trying to find the (img) code on Flickr but it isn't working :/ **** knows lol
 
I'm trying to find the (img) code on Flickr but it isn't working :/ **** knows lol

Seen the car at a few meets and shows here and there, looks awesome!

To get Flickr images in, get the photo open and click the arrow in the bottom right corner to share the photo. Once that pop's up, select 'BBCode' and then choose your size from the drop down and the link will be there ready to be copy and pasted straight into here.

If you open a photo through your camera roll on Flickr you won't see the share button and need to click 'View on photo page' in the bottom right corner then you will be in the right place.

For Imgur, copy the direct link to the image which you will see when you open your photo up. Then paste it into here and stick '
' after the link. Example -
 
The pictures work on tapatalk rich, strange, oh well I'll use this from now on as it seems much easier.

Car should be off the road for winter for a few rust repairs and maybe subframe bushes etc.
 
658d2f1fa9afd04605db6e6f06f8a437.jpg
45e9424a4718fee287e75c7718ffe52a.jpg


Got myself some 3 piece ssr koenigs, the fitment isn't very good but I plan on getting wider lips asap, I do have all 4 but only got decent tyres on 2 currently.

The car will be coming off the road for winter for a good clean down and fixing stuff. Also hope to get skirts, spats and wheels sorted over winter!! :)


Sent from my iPhone using Tapatalk
 
Not made any progress recently, actually the car has gone backwards, I moved house so finally have a garage to store the car and can do work on it without dying in the cold!! However, the car didn't get touched for about 3-4 months and when I started it a few weeks back it had developed a worrying rattle at around 3000rpm :/
I showed the video to a few people and they all agreed that it was probably the bottom end chattering. So me and a mate spent a couple of days tearing the engine out and inspected the damage. Bearing no.3 has basically worn through to the backing and was very close to either completely shattering or maybe spinning etc.
As the engine hasn't ever been opened until and has done 158k I'm not too surprised, the crank however doesn't look damaged so I will be getting it measured and polished.
I'm also going to get a new oil pump, head gasket, piston rings and obviously new bolts and a timing kit. If I can afford to do a fair few upgrades I will as I have a t28r that needs a rebuild lying around and stuff.

So, hopefully I can get it back together with few as possible issues and the car should be better than ever!! Doesn't look like I'll be driving it in 2018 though:(

ca742b269d26efcf29cc22cf12710be1.jpg
4c3c73482f16482937c3c174e2ee3bee.jpg
bc12843aeca410c7fbb8e087a9edc4aa.jpg
b982e579da2725a6d60cad7adbef6fdc.jpg
69e1d8be1b10632f675077106abfe031.jpg
f3347eb3c81c5d1229bd826fa946d26c.jpg
469ee1eb170b13a69a86605d8101c3ae.jpg
a5f9b292707f71c227ed74cbf4911d10.jpg
cc57ef4b0ac75ae0870a9d785a9ef781.jpg
00c8c8f301902c97baf9f930d7cc2a3c.jpg


Sent from my SM-G950F using Tapatalk
 
Good luck with her man I rather like your cars colour it looks great in person ;)
Congrats on the garage :)
Mines been off the road too since last April with a spun bearing, only just bought a replacement engine.
Really hope I can get it back on the road for summer!
 
Last edited:
Just thought I'd do a small update, the car now has a less ****ed sr20 (hopefully) installed, it's got a new competition clutch stage 4 6 paddle clutch with lightened flywheel, japspeed manifold-the thicker apparently half decent one. Updated the cooling system with a fenix radiator and twin fans-wired into the original factory loom for the front fogs. T28r etc. Might eventually get some better injectors but ideally I'd want to go for full standalone I just don't have the funds currently.
It basically needs the oil I've just bought changing in, starter motor connected and it should be good for a test fire up. The only small issue is all the rust I've found, however me and a friend (who is a welder) are going to get cracking on that in the next week.
The plan is to get it mot'd and on the road before June!!
d133e17c428ed660b8c3a2720815625f.jpg
13583f4f10f46d982002bc2777b72199.jpg
395328a9ee2454d7e6841f65a194a441.jpg
fb97b157cd10ae93c6e1cce7b42abfc8.jpg
826f980fe125599e8a56130239a90de3.jpg
dd8cbf6cdcb0bdd2254543a2eae09cc9.jpg


Sent from my SM-G950F using Tapatalk
 
not that one, I’m in lords wood, been tempted to ask about that one in totton
Oh right, damsen is a really nice colour man. I also live in totton. Do you drive yours every day or is it just a toy??

Sent from my SM-G950F using Tapatalk
 
Back
Top