What kind of products are you looking for?

[MazworxRacing]

I see that we've put up a few things but not much interest on them. Just let us know what you guys are looking for and we can try to provide it for you.

Thanks!

[Pablo13]

Id like too see some CA based headwork that will allow for 8k rpm and over.

Oh and welcome :wave:

[ex-ctr]

dry sump set up for an sr20det:)

[MazworxRacing]

dry sump set up for an sr20det:)

Full out race car? Running alternator?

[ex-ctr]

Full out race car? Running alternator?

i can move the alternator as do need one :nod: im not using aircon or power steering so there's room to reposition, im also using an ATI main pulley so i can bolt a drive wheel to that:nod:

[MazworxRacing]

i can move the alternator as do need one :nod: im not using aircon or power steering so there's room to reposition, im also using an ATI main pulley so i can bolt a drive wheel to that:nod:

What chassis is it in?

Im pretty sure we can put together a dry sump setup for you no problem.

Here is a look at the setup in our S15 drag car.

http://i597.photobucket.com/albums/tt51/mazworx/DSC00999.jpg

[ex-ctr]

S14 shell, so thats where i got my exhaust manifold idea from, my hx35 sits in the same place as your monster turbo:nod: also how much roughly will it cost

[MazworxRacing]

S14 shell, so thats where i got my exhaust manifold idea from, my hx35 sits in the same place as your monster turbo:nod: also how much roughly will it cost

Ok. That's actually the "smaller" turbo. The one on there is bigger now :)

Ill put something together for you and PM you in a bit.

[ex-ctr]

Ok. That's actually the "smaller" turbo. The one on there is bigger now :)

Ill put something together for you and PM you in a bit.

:thumbs: and the pound seems to be getting stronger against the dollar:nod::)

[DREAD13]

A stroker kit for the CA18DET! :wave:

[MazworxRacing]

A stroker kit for the CA18DET! :wave:

If there is enough request for it, sure why not? :)

[kingj]

Do you/can you do any deals on alloy wheels in good width and offsets? 5zigen,xxr,cst etc? basically ones we dont really get over here unless we pay silly money for! but are cheap in the USA, new or used:)

Yes we can get wheels. Just let us know what you are looking for :)

[Aj82]

Possibily a nice polished and shaped inlet manifold similar to the Ikeya ones? Just an idea as im guessing these could be just as expensive as the Ikeya ones but i would be interested.


Cheers Aj

[ex-ctr]

Ok. That's actually the "smaller" turbo. The one on there is bigger now :)

Ill put something together for you and PM you in a bit.

have you managed to work out any details/price yet:)

[MazworxRacing]

have you managed to work out any details/price yet:)

Working on it as we speak should have a quote real soon :)

[adzn2k]

rb20det stuff like forward facing intake manifolds, conrods and pistons :)

[ex-ctr]

what 1000 top feed injectors do you do, also intrested in a fuel rail :nod:

[MazworxRacing]

what 1000 top feed injectors do you do, also intrested in a fuel rail :nod:

We have RC Engineering injectors for top feed.

Ill double check to see if our fuel rail will work.

[ex-ctr]

We have RC Engineering injectors for top feed.

Ill double check to see if our fuel rail will work.

i was thinking of RC injectors:nod:

[SILBEAM]

can u tell me how much for just the dry sump oil pan and will it fit rwd sr or is it for the fwd sr as thats whats in your car is it not ..thanks

[MazworxRacing]

can u tell me how much for just the dry sump oil pan and will it fit rwd sr or is it for the fwd sr as thats whats in your car is it not ..thanks


The motor/pan is RWD. We just used the FWD VVL head on it.

The custom oil pan is 550.00USD + shipping

[keggy]

uprated gearbox internals:D

[SILBEAM]

i was always lead to beleve that fwd heads will not fit rwd blocks because of the extra oil drain so is it just the ve head that fits or is it any ... plus have you any pics of the oil pan ...thanks

[MazworxRacing]

i was always lead to beleve that fwd heads will not fit rwd blocks because of the extra oil drain so is it just the ve head that fits or is it any ... plus have you any pics of the oil pan ...thanks


We've only tested the VE head it seems to be the better head out of any Nissan 4cyl setup.

We dont have any pics of the actual oil pan. Maybe one day we get the race car on the projacks I can probably snap one.

[McLarenboy]

I'm very keen on straight cut gears, or dogbox. If you can get your hands on anything for the CA18 then i'd really like to know the price so i can start saving...

[dukey]

what can you do in the wayof fuel tanks and delivery systems?

[MazworxRacing]

what can you do in the wayof fuel tanks and delivery systems?

Is there something specific you are looking for?

[dukey]

just trying to find out my options at the moment really.

[SteveB]

a ca18det inlet plenum would be nice :D

[MazworxRacing]

I think we are going to put making anything for the CA on hold because we've tried to offer stuff out there but no one seems to be interested.

[Streetmekanik]

A kit that fits the Nissan VK engine in a S-body with a manual transmission.

[Aj82]

i was thinking of RC injectors:nod:

Iv ordered these! woohoo. Interested in the fuel rail aswell.

Cheers Aj

[Aj82]

Possibily a nice polished and shaped inlet manifold similar to the Ikeya ones? Just an idea as im guessing these could be just as expensive as the Ikeya ones but i would be interested.


Cheers Aj

Bump for the sr20:thumbs:


Cheers Aj

[MazworxRacing]

If you check our blog, we've designed the intake manifold flange already done. Just gotta work on the runners now from the drawings, its gonna be really really nice.

[Aj82]

Ohh forgot about that. Let me know on the progress guys.

Cheers Aj