View Full Version : Lambda sensors
A lot of the cars we get in the workshop and faultly lambda sensor, so now we stock plug in lambda sensors for the 200 :)
They're £69.99, less than half the price of Nissan sensors!
The come with OEM type plug, so they're a direct fit with no soldering/wiring.
We currently have S13 and S14 sensors in stock - The S14a uses a longer cable (you can get the sensors we have in stock to fit, but its a bit of a faff)
We'll be getting the S14a specific ones in soon.
Click here to order: http://www.h-dev.co.uk/index.php?cPath=78_82
http://sxoc.com/vbb/attachment.php?attachmentid=49114&d=1190103346
could a dodgy o2 sensor be causing my symptoms?
Razzario
18-09-2007, 11:38
oem lambdas @ 69.99... have you gone mad jez?
could a dodgy o2 sensor be causing my symptoms?
Maybe - to check you need to hook up nissan datascan, then with the engine warmed up, hold the engine at about 2krpm - the o2 sensor reading should flick back and forth a couple of times a second. If it just stays still then its probably knackered.
do you have a date for the s14a sensors yet Jez??:)
Not yet - they're on their way though :)
The S13/S14 ones fit, but you have to mvoe the plug on the loom - not ideal really.
think i'd rather hang on for the 14a specific one really. i'll keep watching this thread for an update.
thanks for the speedy reply too:thumbs:
mark_200s14a!
26-09-2007, 18:12
i will have a s14a one mate as i need one after you said mine was dead when you mapped it.also when i get one from you any chance you can check my avcr as it was saying the injectors were on 100% if you remember.cheers
S14a sensors in stock now!
i need one! how do i get one Jez?
http://www.h-dev.co.uk/index.php?cPath=78_82
ordered:) this should get the old girl going properly again:D
ordered :) top work fella :thumbs:
my s14 has had the lambda removed for watever reason in the past, will i see a big diff fitting a new one or are they not needed?
You'll probably need one to pass the MOT and you may see slightly better fuel economy
RADS_S13
11-10-2007, 14:41
if mine doesn't pass its MOT I'll be giving you a bell mate, as mines a bit suspect could probable do with one anyway.
Richy_Boy
11-10-2007, 19:54
Jez, if you have an 'a' lambda in stock still can you put one by? I'll run past your gaff sometime next week and swap them if that's OK?
Rich
Wish i seen this thread sooner!! Just got one off nissan for £124 :cry:
Jez, if you have an 'a' lambda in stock still can you put one by? I'll run past your gaff sometime next week and swap them if that's OK?
Yup - them stock at the moment :)
Best make it early next week, they're selling fast
Richy_Boy
11-10-2007, 23:44
:thumbs: :D
If I get dragged into work tomorrow (planning to work from home right now) I'll give you a shout... otherwise, Tuesday at the latest.
Rich
Recieved mine:thumbs:
I actually had a card from the postman on thursday having only ordered on wednesday afternoon......top service, thank you:nod:
Richy_Boy
15-10-2007, 13:10
No probs :)
Hey Jez if you're about this afternoon is it OK to pop over and buy one of your fine S14a lambdas (and ideally fit it using your tool :smash: ) ?
Do you take debit cards or will I need to swing by a cash machine first?
Rich
No probs - cash prefered but can do cards :)
Richy_Boy
15-10-2007, 13:25
Cool, cash it is :thumbs: I'll be leaving here about 4pm so should be at yours for 4:30 easily I'd imagine. :)
Rich
Hi Jez just completed my order please do let me know you have recieved payment via paypal.
Yup - It'll be with you Wednesday :)
I fitted mine yesterday - went in perfectly (as expected of course :D) and car is working just nicely thank you :D
Top work fella :thumbs:
I just wanted to let users know that the service I got from Jez in terms of the fast delivery and keeping me informed was AMAZING !!
Thank you Jez.
Just having so much difficulty getting the Bleeding old one out !!!
TOP SERVICE !!:thumbs:
Cheers - glad you got it ok :)
Getting the old sensors out can be a right pain in the arse...
Jez
one pin on the ecu is working, 111 changes from 0 to 12v at 4000rpm, but pin 19 is a constant 0.2v
is this the usual failure mode?
and have you got one in stock for a 14A?
Jez
one pin on the ecu is working, 111 changes from 0 to 12v at 4000rpm, but pin 19 is a constant 0.2v
is this the usual failure mode?
I'm not sure to be honest, I usually just look in consult.
and have you got one in stock for a 14A?
Yes :)
Just found a free keyring in the bottom of my envelope:D cheers Jez:thumbs:
just ordered one on your website mate
fitted it last night (note, I didn't say I fitted it) ;)
and could I just say in the world of 200 repairs/mods where we have got used to cheaper non nissan alternatives needing a great deal of fettling to make fit or work, what a refreshing change it was for a genuine replacement, that didn't need the loom chopping to fit, with a cute little sachet of copper grease, and two ickle cable ties.
sir i salute you.
BLAKTOOTH
04-01-2008, 14:39
Just wondering how these sensors compare to the standard nissan ones? I know they're a lot cheaper but will they last? I only ask as I have heard bad things about non nissan lambda sensors in that they don't last five minutes.
I've sold a lot of these lambda sensors and never had one returned - they seem very good quality and have factory fit electrical connections.
i've done a fair few thousand miles on mine now and all is well:)
Micraplay
05-01-2008, 00:42
is either the s13 or s143 sensor suitable for use on a redtop s13 SR??
makes no difference to hoe the car runs whether mine is plugged in or not! ive tried altering the sensor setting on my power fc too and it still makes sod all difference so i assume my sensor is goosed
The sensors I sell with work on retty much any Nissan :)
You need to do a proper check of the lambda sensor to see if its working properly. See if the voltage is swinging from 0 to 1v a couple of times a second.
Micraplay
05-01-2008, 16:50
i should be able to see that on the power fc commander shouldnt i?
Yeah, IIRC you can see it in the sensor check screen.
Micraplay
05-01-2008, 17:16
ok cheers, will have a look
Micraplay
05-01-2008, 17:54
just been out and checked, turned on the 02-1 sensor function, then held the revs around the 2k mark. Got no reading for the o2-1 sensor. very occasionally when blip the throttle or something it will read 0.02v then flick back to zero.
If you think i need a new one, theni'll have one. A friend of mine is coming to you on monday morning with an S14 Silvia, quite nice it is too and i'll get him to get it off you while he's there.
also, is there a way i can adjust the TPS and CAS using the FC commander as a guide? I have a feeling they're both miles out. the TPS on the redtop SR is in a really crap place too! just so i can get it set reasonable until i have it mapped, i dont thrash it. (will be having a full map once ive sourced some nismo 555's and installed my tomei cams - anything else recommended like valve springs, stoppers etc?)
Do you have these in stock at the moment?
Do you have these in stock at the moment?
Just sold out - I've got more on the way :)
Should be here in a couple of weeks.
Just sold out - I've got more on the way :)
Should be here in a couple of weeks.
ARGHHH!!!!!!!! Nevermind. Would it be OK to put my order in now so that you can ship as soon as you receive?
Cheers :)
Micraplay
08-01-2008, 20:12
my friend informed me that you'd run out of sensors. (he's proper pleased with his results from your re-map too)
if you could post when you get them back in stock and i'll see what the funds are like!! thanks.
back in stock now :)
Jez,
I've just ordered one from your website. If there's still a choice of fitments, can you send the shorter cabled one for the S14.
Thanks
Tim Barlow
They all come with the longer cable now - its easy to tuck the extra away with no problems :thumbs:
They all come with the longer cable now - its easy to tuck the extra away with no problems :thumbs:
OK. Thanks
It arrived early this morning. Thanks :thumbs:
Just got to get the old 'un out now :smash:
just ordered mine off you :)
when roughly should i expect it to arrive jez?
blooming eck'
Fast delivery and super fast response!! Can you come fit it aswell ;)
Hi Jez,
I'm looking for a Lamda sensor for a S14a, do you have any in stock? One that is plug and play?
Cheers,
Mark.
Yup - in stock and plug and play :)
Cool, had jumped the gun and place an order last night !
Cheers ! ;)
how much for the delivered?
£75.49 http://www.h-dev.co.uk/product_info.php?cPath=78_82&products_id=135
mixmasterspike
06-06-2008, 16:10
do i really need one? i currently run an aem afr wideband and use an safc 2 to adjust the fuel.
When does the original lambda come into play i.e what percentage of throttle or rpm?
I should really check mine first though:rolleyes:
BONEZ007
07-06-2008, 09:32
hey jez, ime thinking i need to get a new lamba too, cuz my s14a is running very lean. is there a way to test it to see if it is no good ?
do you have the s14a in stock too ?
gonna go look on ya site before i order tho might see something else :thumbs:
do i really need one?You should have one really - it sorts out the fueling on low load and will probably pay for itself in a few months through saved fuel.
hey jez, ime thinking i need to get a new lamba too, cuz my s14a is running very lean. is there a way to test it to see if it is no good ?
do you have the s14a in stock too ?
gonna go look on ya site before i order tho might see something else :thumbs:
You can test the lambda sensor with consult or a multimeter - see the service manual for details.
We have the sensors in stock :)
BONEZ007
08-06-2008, 12:27
ok nice one mate :thumbs:
Going to order one of these today as mine is shagged:eek:
im getting 50 miles to 20 pounds worth of fuel
thats not good :no:
BONEZ007
13-06-2008, 19:47
hey mate can you send me a s14a one please :thumbs:
do you still have my details ?
cheers :thumbs:
I don't know who you are - could you email me or order online :)
Jez, I will probably need one for my S14A. Could you put one aside for me? I'll let you know either way. Cheers.
I've got quite a few in stock - just order on line or phone when you're ready.
BONEZ007
13-06-2008, 23:07
ok mate ile register and order on your site:)
BONEZ007
13-06-2008, 23:27
just ordered mate used paypal tho cuz ime on my ps3 browser:wack: names nic jones, so you now no who i am:thumbs:
Just ordered mine Jez. Can you bung me a PM to let me know when it has been sent?
Cheers dude.
mixmasterspike
17-06-2008, 00:58
ordered one via your site jez:thumbs:
BONEZ007
17-06-2008, 10:36
just come mate :)
will get it fitted later :)
cheers :thumbs:
mixmasterspike
17-06-2008, 16:26
ordered one via your site jez:thumbs:
sorry jez i forgot to add a multi layer sr gasket for head/manifold
I sent you £19.99 via paypal seperate:rolleyes:
I've just emailled you :)
little_ant
08-08-2008, 15:57
my standard lamba is holding a constant 8v throughout the rev range causing it to over fuel and idle badly, have disconnected it and it runs alot better, would this point to a fooked sensor, this may seem a stupid question but i just wanna confirm it before i order a new one
Just put in an order for one. My S14 didn't pass the MOT emissions test and seems to be running really rich. No wonder the fuel consumption isn't really where it should be.. :)
You should get it tomorrow :)
You should get it tomorrow :)
Yup, the sensor got here in just one day. Thanks!
jez do you have a s14a sensor in stock?
also have you ever seen a hd stage 1 chipped have a o2 sensor reading like one in the attachment while on idle??
We have them in stock
The trace you have there looks a bit odd - it should go up and down in a sine wave. Try holding the revs at 2500rpm and see what you get.
Powered by vBulletin® Version 4.1.9 Copyright © 2013 vBulletin Solutions, Inc. All rights reserved.